Is it possible to remove the stretch ceiling. Is it possible to pull a stretch ceiling? How to do this and why is the help of qualified craftsmen important? Removing the film

Stretch ceilings for the second time ... is it real?

We can no longer imagine a successful solution to our interior without stretch ceilings. After all, thanks to them we get the maximum beauty in terms of design ideas. In addition, the process of installing stretch ceilings is very fast, simple and at the same time effective way. However, we cannot foresee everything. possible situations, which may occur after the installation of stretch ceilings. This means: “the neighbors from above flooded you”, redevelopment of the interior, requiring violation of the integrity of the ceilings, etc. And naturally, the question may arise about reuse stretch ceilings. This is what we'll talk about later.

It can be unequivocally stated that such a process is feasible. But it is necessary to take into account the most important aspect, on which this whole idea will literally depend - the work should be carried out only by specialists in this area, professionals, regardless of whether you install the ceilings for the first time or the second, after dismantling the first. And the secondary stretching especially requires a professional approach, since this process is much more complicated than the previous one.

Variety of material.

Usually there are two main types of material that are used most often and successfully. First of all, this film version and fabric. Naturally, everything will depend on your individual choice. But it is worth noting that the use of each of these options requires a separate and individual approach in terms of technology and installation mechanism. Although as a result of the use of these two materials, you will in any case get the desired stretch ceiling.

Stretch ceiling fixtures.

The fastening of a stretch ceiling depends primarily on the choice of material. Since there are fasteners that are inherent only to a certain material variant for a stretch ceiling. Therefore, it is very important to first decide what material will be used in the future. This topic is very broad and requires detailed description to show the difference between one or another type of fastening. We are ready to advise you, after your direct choice of a specific material, and offer the most optimal view mounts.

Dismantling.

Again, when we come to the process of dismantling, we must again draw Special attention on the material and type of fastening. Since all these processes are very intertwined. Especially it depends on the chosen material. false ceiling. Since the successful process of dismantling each of existing material, and also subject to a certain type of fastening, requires an individual technological approach.

The dismantling process itself also requires a specialized and professional approach, and also requires certain experience in carrying out such work, since a number of related technological difficulties may arise in the process of removing the ceiling. Unfortunately, a person ignorant in this matter can cause irreparable harm to the stretch ceiling.

Therefore, in order to avoid any negative unforeseen situations in this process, we suggest that you use the services of specialists, so you are guaranteed perfect solution question in the end. At the same time, the guarantee and the company is based primarily on the work of first-class specialists and professionals, the presence of vast experience in such operations, as well as the availability of all necessary tools that will allow you to successfully complete the task and within a strictly defined time frame

The fabric of the stretch ceiling can be removed with your own hands, without resorting to the help of specialists. To do this, you need to know the features of the mounting structure (baguette) and the properties of the material from which the ceiling is made. Ceiling upholstery and even complete installation designs don't take long.

You will immediately understand the presence of moisture on the stretch ceiling

The owner of the apartment can dismantle old ceiling due to its damage (gusts, streaks, stains, mold formation, flooding and strong stretch marks, warping of the canvas due to wall deformation). Sometimes the canvas is changed to install a ceiling of a different color and texture or new electrics. Both the PVC film and the fabric can be removed from the baguette (frame) and then installed back.

Room preparation

The ceiling is upholstered in a pre-prepared room. Items that can be damaged by high temperature are taken out of the room (if a heat gun is to be used).

If water has accumulated on the stretch ceiling, it is enough to dismantle one part and drain it

Aquariums are removed from the room, pets are removed. You also need to remove any things that will interfere with work. The lamp is removed from the stretch ceiling and removed to a safe place. You can remove the lamp yourself, but if the mounting is difficult, you need to contact an electrician. Removed and removed ceiling plinth or masking tape.

Tool and equipment

Before you remove and reinstall the canvas yourself, you need to purchase necessary equipment, materials and tools. For work you need:

stepladder or sturdy table;
heat gun (for heating the vinyl sheet);
construction spatulas, from which you can make blades and hooks, or special factory blades with a curved end;
clips with cords for holding the removed canvas on weight (crocodiles);
mounting tape;
pliers with long narrow ends;
insulating tape;
screwdriver;
construction knife.

Often masters invent their own tool for dismantling work. So, for example, metal building spatulas are narrowed, grinded so that they become blunt, the corners of the working blade of the spatula are rounded off.

Spatulas for stretch ceilings

Spatulas and pliers handle sandpaper to remove all burrs and smooth out roughness. The blunt blade is bent so that it is more convenient for them to reach the protrusion of the profile against which the harpoon rests. Any tool used during the work should not have sharp corners and rough surfaces in order to avoid tearing the web.

Before you remove the stretch ceiling, you need to find out how it is fixed in the profile (this data can be found in the contract that was drawn up with the organization that did the installation of the ceiling). There are three types of web fastening in the profile: harpoon, wedge (glazing bead) and clip-on.

How to remove a stretch ceiling with a harpoon mount

Harpoon - a plastic flexible bar, which in cross section is a hook (or harpoon, where the name comes from). The bar has an average rigidity and is produced by the footage.

PVC canvas is marked and cut out, exactly copying the shape of the ceiling. A harpoon is welded to the edge of the canvas, along its entire perimeter. This is done using HDTV equipment, which is available at enterprises that install stretch ceilings. When the harpoon is welded around the perimeter, it is firmly butt welded. The harpoon is inserted with a spatula into the groove of the baguette (profile), where it is fixed on the inner ledge of the profile with its hook.

If the film is edged with a harpoon, it will not be difficult to remove the stretch ceiling with your own hands. To vinyl ceiling became more flexible and stretchable, it is evenly heated with a heat gun. Recommended temperature heat flow- 70 degrees Celsius. Padding of the ceiling starts from the corner of the room. Some home craftsmen heat only the corner from which the harpoon begins to be removed, and use a hair dryer to heat the vinyl.

Harpoon fastening of stretch ceilings

When picking up PVC sheets it is necessary to remove the harpoon from the ledge (shelf) inside the profile. If this was done in one place, then the rest of the canvas is removed by simply pulling on the harpoon. The order of work will be as follows:

Heat evenly suspended ceiling, starting from its central part to the corners.
Take a bent spatula and a screwdriver.
Find a place in the corner sections of the ceiling where there is a sufficiently large gap between the wall and the surface of the canvas. It is necessary to ensure that there is no place for gluing the harpoon end-to-end in the removal area. This place is not very strong, it can break the film under physical impact.
Using a screwdriver, squeeze the harpoon, insert a curved blade into the slot and hook the harpoon.
To release the harpoon, they drive with a spatula to the right and to the left by 10-15 cm, thereby the harpoon is slightly squeezed out of the baguette.
On the other, perpendicular wall, the same is done. Thus, the harpoon in the corner of the room will be hooked by 2 spades.
The shoulder blades are parallel to the wall with a slight effort to pull down. The blade with the harpoon comes out of the profile.
Then the blades are moved along the walls and the film is carefully pulled out. If the ceiling area is large, the canvas, in order to avoid stretching and deformation, is hung on clips (crocodiles).

If the ceiling area is small, the vinyl film can be removed without preheating, for large canvases preheating required.

Dismantling the ceiling with bead (wedge) fastening

Is it possible to remove a stretch ceiling with a glazing bead? It is possible, but you need to keep in mind the fact that it will be difficult to put it back, since after installation the builders leave very little stock of the canvas, but if there is a stock, this is possible.

Bead (wedge) - special plastic profile different section. The glazing bead is inserted inside the profile, tightly pressing the material. This type of fastening is used when mounting both vinyl and fabric ceiling structures.

In order to remove the PVC film or fabric, you need to pull the glazing beads out of the profile by hooking them with some curved tool (curved spatula, spatula, hook). Dismantling begins in the corner of the room.

The PVC film is heated with a heat gun before dismantling. The fabric does not need to be heated.
The profile is slightly unclenched using any handy tool(for example, a thick screwdriver, pliers with long ends).
Behind the glazing bead, a curved shoulder blade (or two) or a hook is carefully inserted and pulled down. The glazing bead comes out and the canvas is released. This must be done very carefully, as the edge of the vinyl film or fabric is not protected by anything and is easily damaged.
At large area the ceiling, the released canvas is hung on clips with cords.

Removing the ceiling with clips

Only slightly extensible fabrics with polymer impregnation are mounted in clip-on fasteners. Clip fasteners - a special plastic profile, which in cross section is a clip.

Cam fastening of a stretch ceiling (clip)

The fabric is simply tucked inside the clip with a spatula, and the clip holds the fabric and prevents it from coming out.

Dismantling the seamless fabric ceiling start from the middle of the wall, not from the corner.
To remove the canvas from the clip profile, you need to moderately press on the canvas in a place adjacent to the wall. In this case, you can slightly open the mount with a screwdriver or thin pliers.
The tension on the fabric will loosen and it can be gently pulled out of the attachment.
If the fabric was cut very short when installing the ceiling, it will be difficult to tuck it into the mount during subsequent installation.

How to remove the side of the stretch ceiling with your own hands, without damaging the frame and PVC film, will be described in this article. French or PVC ceilings are a fairly strong and durable structure, designed to last 15-20 years. Mounting features make them not susceptible to the settlement of buildings and sagging of the carrier plate.

But, life makes its own adjustments to human plans. Moreover, these adjustments are not always pleasant, and, as a rule, at the wrong time. Often it may be necessary to remove the tension web. There can be quite a few reasons for this: the neighbors flooded, the electrical wiring failed, or a planned replacement of the pipes of the heating system is underway.

If the PVC sheet is in good condition and suits the owners, then it can be removed and, after necessary work or drying room, install back.

What information is needed to get the job done?

Before you remove the stretch ceiling, you must have certain data on the type of fastening of the web and a brief knowledge of the structure of the coatings.

Ways of fastening the canvas

As a rule, on tension structures a warranty card is issued from PVC film, in which, in addition to the service life, the main specifications. One of these characteristics is the method of fastening the canvas in a baguette. The method of work will depend on this method. If there is no documentation for the product, then the necessary information can be obtained independently by studying the design features.

When installing stretch fabrics, the following types of their fastening in the profile are used:

Harpoon. A fairly common type of fastener. Cloths with such edges are made to order and are the easiest to work with. A rigid edge in the form of a harpoon is welded along the edges of the film. Entering the profile, this edge unfolds and holds the film in the profile.
Clip-on (cam) type. In this case, the fixation of the film is carried out due to the pressure of the elastic plates plastic baguette. With this mounting option, plugs and decorative trims are not used. Installation can be carried out without preheating.
Shtapik type. This type of fastener involves pressing the film against the inner walls of the profile with a special longitudinal product - a glazing bead.
wedge type. Easy to assemble and disassemble system, available for independent work.

In the second and third cases, it should be borne in mind that the canvas was in direct contact with the surface of the baguette and may be damaged.

Features of fixing French ceilings

The main part of the French ceilings is PVC film. It is a durable, environmentally friendly and elastic material. One of its features is an increased reaction to an increase in air temperature. At temperatures above +60º C, PVC film becomes soft and stretches well. As it cools, it shrinks and becomes hard.

Therefore, a special tool is used to install PVC sheets - a heat gun. Before you remove the stretch ceiling, you should take care of its acquisition. For a one-time action, it makes no sense to buy it, but renting it is quite reasonable and affordable. heat gun will be needed both for dismantling the canvas and for its installation in place.

Attention: Please note that PVC film, having incredible tear strength, reacts very poorly to sharp objects. It is easy to pierce or cut. And this is fraught with the replacement of the entire ceiling.

Web removal technique

Demolition work can, in some cases, be more difficult than the construction itself. Question: how to carefully remove the stretch type ceiling on your own, is relevant for many owners of such structures. It is quite possible to carry out such an operation, provided that quality tools, manifestations of patience and consistency in the implementation of all actions.

Tools and equipment

To work with PVC film, rather specific equipment is required, which can not always be found in a home pantry.

So, you need the following property:

With a steel width of 8-10 cm. Before removing the stretch ceiling yourself, it is necessary to round off the corners of the spatula and grind off all sharp edges. If this is not done, then you can cut the film.
Sturdy pliers with long, curved jaws.
Construction knife.
Sturdy screwdriver with a bent end.
Special clothespins for fixing the canvas on baguettes during installation.
Table, ladder or goats.
Heat gun. It is recommended to use a gas-powered machine. The electrical appliance has a large capacity and can damage household electrical wiring.

When the equipment is ready for work, you can proceed to next step- preparation of the workplace.

Workplace preparation

Before you remove the side of the canvas or its entire surface, you need to carry out certain preparatory work.

They include:

dismantling of ceiling lamps;
removal of cages with birds, aquariums and flowers from the room;
protection against overheating of interior items that may suffer from high temperature(TVs, plastic windows, Digital Watch).

After the room and tools are prepared, you can begin to remove the canvas with your own hands.

film removal process

Significant assistance in carrying out the work will be provided by a video on the removal of the canvas of the French ceiling. It will reveal some of the nuances and answer the question of whether it is possible to shoot the canvas yourself.

The technology for removing the web directly depends on the type of installation of the web in the profile. Based on this, the disassembly of the structure is carried out.

Important detail: Answers to the question of how to dismantle the entire surface or how to remove the side of the stretch ceiling must be considered separately, in relation to each installation method.

Harpoon mount

Facing with this option of adhesion to the walls is easier to disassemble than others. Why? The reason is simple: this type of fixation allows easy assembly and the possibility of repeated disassembly of the structure. The separation of the canvas should begin with a part of the wall in the area of \u200b\u200bthe corner.

Removal of the canvas is carried out in the following order:

Detachable decorative strip around the perimeter or only on one side.
With a heat gun, the room is heated up to + 70º C. This is necessary for the canvas to increase in size and relieve pressure on the harpoon mount.
With a blunt spatula, the harpoon is hooked and lifted.
The released harpoon hook is captured with pliers and removed from the profile.
Further extraction is carried out manually without much effort.

Installing the canvas in place is carried out in the reverse order.

Cam mount

Removing the film with this fixation option is the simplest and least expensive, since in this case there is no need to warm up the room. But, extra care must be taken because the spatula will be in direct contact with the film.

To detach the film, you can proceed in two ways:

In the corner of the room and at a distance of 50-60 cm from it, insert 2 screwdrivers between the cams. The pressure of the cams on the segment between them will weaken, which will make it possible to freely remove the film from the clamp. Repeat the operation until the right amount material.
Insert a spatula between the cams and squeeze out the movable one. The material will come out of the clamps due to the web tension. The rest of the material is extracted manually.

It should be remembered that serifs from the clamps may remain on the material. When installing, they can be a kind of guide.

Bead variant

In this case, you will need a screwdriver, a spatula and a heat gun.

The sequence of work is as follows:

The room is warming up.
The decorative cap is removed.
In the corner with a spatula is squeezed out outer wall a baguette, and a glazing bead is hooked with a screwdriver and removed.
The glazing bead is intercepted by hands and pulled out of the baguette.

If there is a sufficient supply of material, it may well be inserted back.

wedge method

The easiest way to remove film.

The sequence of actions is as follows:

A decorative insert is detached, which plays the role of a wedge, which causes a release of pressure on the plug.
The plug clings to the edge with a screwdriver and is removed from the baguette.

The cloth freely gets from a groove.

Thus, it is quite feasible with our own hands, subject to certain technology.

In what situations may it be necessary to dismantle the ceiling?

Sometimes there are situations when you need to dismantle the stretch ceiling, but I would like to put it back in place. For example, you want to make repairs to the walls, lay tiles, rewire, it became necessary to soundproof the ceiling from the neighbors from above. But stretch ceiling yours is still good! There are even situations when the customer and the installer do not fully understand each other and the customer receives something completely different from what he expected. In these situations, the question arises: Is it possible to somehow remove the stretch ceiling, and then, after various dirty work, install it in its original place?

Reuse of stretch fabric.

To understand whether your canvas can be reused, you must first figure out what material the entire structure is made of. You also need to understand what method of attaching the canvas was used.

In most cases, the sheet can be carefully removed for later use. The question is whether you are qualified enough for this procedure. Plus you will need special tools:

gloves;
scissors;
pliers with long jaws;
mounting spatula;
mounting clips;
screwdriver;
screwdrivers;
special construction knife;
heat gun (if the film is vinyl);
stepladder.

Ideally, entrust this work to the company that did the initial installation of your ceiling. In this case, it will be possible to avoid or minimize options for damage to the canvas. The installers who pulled the canvas will know all the nuances of the room, understand where to start dismantling.

It should be borne in mind that even if you yourself were able to dismantle the ceiling, this does not mean that you can put it in place.

Currently, such ceilings are mainly made from polyester. vinyl films. Fabric webs are usually placed on profiles with a clip system. In this case, precise cutting of the canvas is not required: the material falls on the object in the form of a cut, which slightly exceeds the area of the room. After filling the film into the profile, the craftsmen cut off the excess material. If such a ceiling is removed, there will not be enough fabric left for re-stretching. That is why after removing the fabric ceiling, you will have to re-order the canvas. But this can just help if, as a result of repairs, you have reduced the area of \u200b\u200bthe room. Wall leveling or laying tiles, can significantly reduce the area, and your canvas will be suitable for a new stretch.

Approximately the same system is used when installing glazing bead ceilings. It is used when mounting stretch fabrics made of polyester fabric and pvc films. In this case, as in the first example, an approximate cutting of the material is performed, and the excess is cut off after refueling. Therefore, it will be possible to re-install such a ceiling only if the area of \u200b\u200bthe room has decreased.

It will be possible to reuse the stretch fabric if the ceiling is made of a vinyl film, which is fixed into the profiles by a harpoon method. And if the area of \u200b\u200bthe room did not change. This method uses precise cutting of the canvas to the size of the ceiling, taking into account the shrinkage of the material. A special profile or hooks are welded along the perimeter of the PVC film, which are inserted into the profile and provide secure fastening with walls. Such a ceiling can be reused as much as you like. The main thing is to carefully dismantle the canvas.

Remove and install the ceiling yourself: pros and cons

Now you understand whether it will be possible to use the stretch ceiling again. But is it worth it to perform such a complex procedure on your own, because there is a risk of ruining everything? Our experts categorically do not advise to remove and install stretch ceilings with your own hands.

In addition, in this case, you lose the right to warranty service your ceiling structure. And damage to the coating will lead to the need for it complete replacement. Therefore, without experience with stretch fabrics and special tools, you should not risk your ceiling. The best thing is to entrust the dismantling and re-installation to our installers. They will do this work quickly and efficiently, so that you can enjoy a flawless and perfectly even stretch ceiling for many more years.