Hello everybody!
A toolbox today is a very indispensable thing for every owner. Most of us have a lot of different tools that we may not use very often, but nevertheless, we keep them, since not one repair can do without them. In order for the tool to be in one place, and it was convenient to transport it, we use special boxes. Often we just buy them in the nearest store, the range and variety allows us to do this. But why not make it yourself? The manufacturing process is not too complicated, anyone should be able to handle it, especially with a handmade thing, which is much more pleasant to use than a purchased option. This article will describe 4 different ways to make boxes, a photo report is attached.
Let's start making!
Manufacturing Method No. 1
We will need:
Material
Plywood;
- pine board;
- nails;
- wood glue.
Tool
- drill;
- a hammer;
- chisel;
- manual frezer;
- ruler;
- pencil;
- roulette.
The first step is to find the necessary material, plywood or trimming boards are suitable for this. Further, according to the presented drawing, it is necessary to mark up, then cut out all the details of the case. It is necessary to make special grooves into which the partition will be placed, for this we use a manual milling cutter, or another available tool.
The diagram shows the following body parts:
1 - wall (2 pcs.);
2 - sidewall (2 pcs.);
3 - bottom;
4 - groove along the thickness of the partition and a depth of 1/2–1/3 of the thickness of the material
When everything is ready, all elements of the box body should be sanded. Next, we assemble the body together, fix the parts with wood glue, and then additionally fasten with small nails.
Now we make a partition for the box, cut out a special handle, for this we use a jigsaw.
When the partition is ready, grease the grooves with wood glue and install it in its place.
Next, from the planks we make overhead handles, with the help of a planer we round the corners. Then we make tool holders from the rails, use a jigsaw, and a drill. The holes will serve for screwdrivers, and pliers, etc. will be installed in square cutouts. tool.
In order for the box not to get dirty, and to be protected from the environment, we cover the surface with varnish. As a result of the work done, we get such a homemade box.
Manufacturing method No. 2
Drawer-stool
Material
Plywood or OSB;
- wooden beam;
- self-tapping screws;
- wood glue.
Tool
Available cutting tool;
- screwdriver;
- ruler;
- pencil;
- roulette.
We take an existing sheet of plywood, make markings on it, and, according to the dimensions presented, cut out the lid (Fig. 1), then the longitudinal sides (Fig. 2) and sidewalls (Fig. 3).
Next, we take a wooden beam with a section of 40x50 mm, cut out a handle, and 4 legs with bevels at the ends at an angle of 15 °.
Next, we assemble the structure together, using self-tapping screws as fixing elements.
Parts layout:
1 - cover;
2 - tsarga;
3 - handle;
4 - leg;
5 - sidewall.
When everything is ready, use sandpaper or a grinder to round off sharp corners and clean the surface. Next, you can apply a protective coating.
The end result should be such an unusual tool box, which, if necessary, can be transformed into an ordinary stool, for this it is enough to turn it over and put it on legs, with it it will be convenient to reach the place we need, at a time when growth does not allow do it.
Manufacturing method no. 3.
Box for the young master.
Does your child love to craft? We offer to make a small box with him, where he will store his favorite tool.
To make a box with our own hands, we need the following
Material
16 mm boards;
- round wooden beam;
- self-tapping screws;
- wood glue.
Tool
Available cutting tool;
- screwdriver;
- ruler;
- pencil;
- roulette;
- clamps.
First you need to take the existing boards with a cross section of 16 mm, then we make the markup, according to the dimensions provided, after which we cut the wood into the component parts we need.
The drawing shows the following details:
1 - sidewall;
2 - bottom;
3 - handle;
4 - handle stand;
5 - holder.
Using sandpaper, we grind the surface and remove sharp corners. When everything is ready, we begin to connect all the parts together, first you need to connect the bottom and sidewalls, then we put vertical racks along the marked lines and at the same time we put a horizontal handle.
We fix everything with glue and screws. Then we install special holders for screwdrivers.
Now you can paint, choose the color and coating at your discretion.
The toolbox is ready.
Manufacturing Method No. 4
The next version of the tool box is well suited for carrying various and necessary equipment for us, its appearance will be distinguished by solidity and reliability.
To make a box with our own hands, we need the following
Material
The board is not thicker than 12 mm;
- self-tapping screws;
- joiner's glue;
- a pen;
- corners 8 pcs.;
- latch 2 pcs.;
- loop 2 pcs.
Tool
Available cutting tool;
- screwdriver;
- ruler;
- pencil;
- roulette;
- clamps.
For the manufacture of the box we use such wood as: pine, linden or poplar. The most optimal thickness of the boards will be a thickness of 12 mm.
Next, we make the markup, according to the indicated dimensions in the drawings, after which we cut it into its component parts, as shown in the photo.
Full list of required parts.
In order to make sure that the wood was cut correctly, you need to put all the parts in a single box.
First, we assemble the bottom part and the lid of the box, for convenience we use clamps and corner clamps. We fix the parts together with carpentry glue.
Then, using a drill, we drill a hole for the self-tapping screws, we drill the holes.
In the course of his life, a person accumulates a lot of small property, which can only sometimes come in handy for some need. In our cramped living spaces, there is often a problem with the location of such things.
To solve this issue, you need a neat container that can be placed in any corner of your living space. The most practical and environmentally friendly option, of course, is a wooden box.
With its independent production, you can use all your imagination and make a unique masterpiece. Fortunately, wood is the material that allows you to make truly original designs.
why tree
For a long time, craftsmen have used wood to make various designs. Houses were built from this material, which served their owners for many years, providing them with comfort and coziness for living.
Wood is a natural material that lends itself well to processing and has high environmental performance. Wooden structures have an aesthetic appearance and exude favorable odors.
Of course, this material has its drawbacks, the main of which are rotting and flammability. But with the right approach to wood processing and caring for it in the future, such troubles can be easily avoided.
Any man wants to produce some kind of product with his own hands. Wood is exactly the material with which you can experiment and make a thing that will not only become a necessary piece of furniture, but also add unusual aesthetics to the interior of a living space.
To work with wood, you will need a special tool that a good owner always has at hand. The choice of material must be approached thoroughly, giving preference to the most durable types of wood, so that the product lasts as long as possible.
The very first thing to do is to determine the place where the wooden box will be located and carefully take the necessary dimensions.
- according to the measurements obtained, we cut out the structural elements of the box - four walls, a lid and a bottom;
- we connect the side walls in turn with the help of nails or self-tapping screws;
- we fasten the bottom of the product, starting from opposite corners, to avoid its displacement;
- Finally, we mount the lid of the box, which we provide the possibility of tilting with the help of piano hinges.
With the help of simple manipulations, the wooden box is ready for use. Finishing of the product is made based on your preferences and tastes.
We are very rarely worried about things and objects that we are forced to use at home, at their summer cottage or in the office. We decided together with you to think about an ordinary wooden box. You can store different things in it, make a beautiful flower pot, a box for letters and correspondence out of it. We look at a photo of a wooden box for different purposes and tasks.
At a manufacturing enterprise, such a container is indispensable as a container, we will talk about the advantages a little later. The most important question that arises: "How to make a wooden box?" To make it, use chipboard, plywood and pine lath.
Today we will start making ordinary wooden boxes with our own hands from wood for correspondence or summer cottages. No special materials and tools are needed here, a standard home kit is sufficient.
Advantages and disadvantages of a wooden box:
- It weighs less than metal containers;
- Only natural material is used;
- Simple assembly of the structure, elementary elements;
- Strength is higher than ordinary cardboard and parchment;
- Low purchase cost of the material, wide distribution;
- With proper surface treatment, the service life increases.
Benefits of using a wooden box:
- Increased weight of transported things;
- A tree treated with an antiseptic lasts a long time.
Ways to use a wooden box:
- In domestic conditions for storage of vegetables, fruit and products.
- Souvenir packaging for a gift.
- Packaging of expensive instruments and equipment.
Attention! When making a box for a specific product or product, its dimensions and weight should be taken into account. Toy boxes have standard sizes and specifications.
Required tools and equipment
Before embarking on a wooden box project, it is required to gather all the tools and equipment in one place.
We will need a woodworking machine, there must be a jointer and a circular saw. Otherwise, we buy the strips we need in the store - size and thickness. You can not do without a pencil, tape measure, building angle and hammer.
We will use the machine for raw wooden blanks, which we will make from a board of 2.5 x 25 x 150 cm.
Instructions for making a wooden box
We take a circular saw and cut it into the wooden elements we need in size, we get edged pieces. First, we cut along the edges, then set it to a width of 20 cm and saw it completely.
Be sure to wear safety goggles while working. It is better if you have a good partner holding the sawn boards.
Having installed the carriage at an angle of 90 degrees, we cut the board into 5 segments, 4 of which are 20 cm, and one more is 24 cm.
Set the planer parameters at a height of 1 mm and process each of the blanks from all sides to get draft versions of the board. For finishing work, the height value should be set to 0.5 mm. The thickness of the finished boards should be 2 cm. We will get boards 2 x 20 x 20 cm.
It is not required to polish the workpiece to a shine, the box will be used to store vegetables and fruits. Tool boxes are made according to the same principle.
We cut the remaining blanks in a width of 4.5 cm, taking into account the direction of the fibers. If you want to make the box ventilated, there will be 3 additional blanks in stock.
Wooden box assembly
The whole assembly process is very simple, no tricks and hidden mysteries. We take the most common nails 5 by 0.15 cm. Why thin nails? So that the structure is tightly fastened and the boards do not crack.
First, we nail the upper and lower planks from the end, then place the remaining wooden blanks. From below we fasten planks 24 cm long to the wooden base, use 35 mm self-tapping screws.
Drawings and dimensions of wooden boxes are presented below.
Wooden box as a flower pot
By its properties and qualities, wood is a versatile material, it can be used to make boxes where we will place our plants.
In the last example, we have already figured out that the tree is very easily processed to a fine state, you can remove absolutely all the bumps and make the surface perfectly smooth. Special skills and abilities are not required for this.
Below we offer to get acquainted with the options for boxes that you can make yourself without any skills with your own hands. The shape and appearance of the structure will depend on your personal imagination.
You can not use an electric tool at all when working with wood, saving a certain amount of money, but much more time will be lost, keep this in mind. With a set of all tools, you will get exactly what was planned in the shortest possible time without making almost any effort.
Be sure to stock up on paint and antiseptic to cover the surface of finished products.
If the box was originally planned for planting flowers, then you can first purchase ordinary plastic pots where flowers will be planted or plant them directly in the box. If you are going to plant in a box, do not forget to spread a film of polyethylene and make holes for drainage.
Photo of wooden boxes with your own hands
Who would have thought that wooden pallets are such a valuable resource! From these boxes you can make a lot of useful things that will be useful to us in everyday life. Our editors will tell you how to make strawberry growing box. To implement this idea, you only need one pallet.
Before reworking an old pallet, inspect its markings. It turns out that some wooden pallets cannot be used for horticultural purposes. If the stamp has the letters MB, it means that the pallet has been treated with insecticides. The letters HT mean heat treatment, such pallets can be safely used for growing plants.
How to make a box with your own hands
You can leave the box in its original form, or you can varnish it. It all depends on your preferences! I dream of placing a similar box in the country, painting it in a bright color.
Detailed master class on creating pallet box watch in this video.
If you like this idea as much as I do, surprise your friends and share!
A box for storing various small things and products is considered an indispensable attribute in a modern economy. Thanks to this design, all things are in their place, while not forming a mess. For example, vegetables and fruits should be stored in a ventilated building where fresh air can freely enter.
For tools, monolithic products without any holes are suitable. For various little things, designs with additional doors and a folding mechanism are suitable.
We offer original options for storage boxes made by hand. Here you will find out what materials and tools will be needed for the manufacture of these products.
What materials are used to build structures?
Most often, boxes are made of wood and other materials. For tools, it is better to choose solid pine or maple. Alder or aspen is suitable for products. These tree species are distinguished by their durability and strength. They do not emit resinous secretions and do not dry out over time.
Plywood is suitable for the manufacture of decorative products. Here you can place every little thing. To fix the parts, a special adhesive composition is used.
Master class on creating a box with your own hands
We offer step-by-step instructions on how to make a box at home. To do this, you will need the following tools and materials:
- tape measure;
- simple pencil;
- board 25 mm thick;
- wooden trimmings 15 mm thick;
- thin plywood;
- metal corners;
- nails and screws;
- hacksaw;
- screwdriver;
- metal hinges for opening the lid structure;
- a hammer.
The first step is to familiarize yourself with the diagrams and drawings of how to make a box. This will allow you to correctly compare the dimensions of the finished product. Do not make structures that are too large, as they will take up a lot of free space.
When all the components are ready, you can proceed to the manufacture of a storage system for vegetables and fruits. The process includes several steps:
On the surface of the boards, we mark the size of the side parts of the product. Next, move on to the bottom of the box. We mark the size on the wooden trimmings. After that, using a hacksaw, we begin to cut the blanks.
We fix the boards together with small nails. We fasten the bottom details using the same method.
The cover of the product consists of a plywood sheet. It is installed on special hinges that allow you to control the closing process.
The do-it-yourself box photo shows the entire workflow.
Tool storage box
This kind of design is considered the best DIY drawer idea. This product will allow you to keep all the working tools in one place. Here you can make additional departments for storing screws, nails and nuts.
For this you need to prepare:
- thin board;
- thick plywood;
- hacksaw;
- electric jigsaw;
- a hammer;
- screwdriver;
- tape measure;
- drawing of the finished product;
- metal corners.
On sheets of thick plywood, we make markings for the details of the box. After that, we drill holes for fastening metal loops. Next, we connect the side parts to each other.
Let's start making the bottom for the storage system. To do this, we attach a thin board to the side of the box. So that it does not fall under the weight of the tools, it must be strengthened with thin boards. To do this, several wooden elements are stuffed on the bottom surface.
In the side parts of the plywood we draw the markings for the handles. They will be cut inside the main body of the product. Here you need an electric jigsaw. The cutting base is installed at the beginning of the markup.
In the process of cutting parts, do not make sudden movements. They can cause cracks on the surface of the product.
Now let's start installing partitions. To do this, cut out a small square from thin plywood. It is fixed with metal corners in the middle of the structure.
The diagram shows a detailed image of the tool box. The drawing shows the exact number of parts:
- side parts - 4 pcs.;
- bottom - 1 pc.;
- partition wall;
- handles - 2 pcs.
DIY drawer photo
Loading...