One of the ways to turn the bathroom into a place where you can not only wash, but also rest and relax is to install a mirrored ceiling in the bathroom. It's not that difficult, but you should choose the type of ceiling. We will also consider its installation.
Pros and cons of mirrored ceilings in the bathroom
To begin with, let's figure out why it has recently become so fashionable to hang mirror coatings in the bathroom, because today in almost every interior and design magazine you can find a photo of such a bathtub with mirror suspended ceilings. The most important advantage is that such a coating visually expands the room - even the smallest bathtub will look several times larger and more spacious.
The second advantage is that the ceiling in the bathroom will become smooth and even, without a single flaw, because the surface must be leveled and covered before mounting the mirror structure. The third visible advantage is ease of maintenance.
To make the mirror ceiling in the bathroom look clean, you just need to wipe it with a soft cloth dipped in a special product once a week. To make work easier, wipe the surface once a day with a dry cloth.
True, it was not without drawbacks. So, for example, such a ceiling, of course, will be quite fragile. However, this minus can hardly be called critical, since the ceiling is rarely subjected to shock and mechanical damage. But it doesn't hurt to be careful. The downside is the rather high cost of such coverage.
Requirements for mirrored ceilings in the bathroom
The bathroom is characterized by high humidity, temperature fluctuations are often observed. Therefore, before choosing a material for the ceiling, let's figure out what requirements a mirror surface must meet.
- Resistant to sudden changes in temperature, steam, water and humidity. These characteristics should apply both to the ceiling and to all fastening details. No need to use non-moisture resistant drywall products, glue and putty.
- Ease of maintenance. Do not forget that the mirror surface will not retain its appearance by itself. If you are not ready for constant complex manipulations, then it is better to choose materials that are easy to care for.
- Construction weight. When choosing a material, pay attention to the weight of the ceiling so as not to create an additional load on the ceiling. Thus, the lighter the coating, the better.
- Safety. Given the conditions in the bathroom, you need to stop at a coating that will not emit harmful substances. In any case, it is better to refuse cheap and low-quality plastic here.
What type of ceiling for the bathroom to choose?
Thanks to modern technology, manufacturers can offer you mirrored bathroom ceilings from a wide variety of materials.
The first type is a slatted mirrored ceiling for the bathroom. He can often be seen in the photo in various magazines. Such a ceiling consists of aluminum strips covered with a mirror coating. These profiles can be made in a variety of colors, making it easy for you to choose the right one for your bathroom design. The main thing is that the colors of the rails do not contrast with the shade of the mirror panel. Despite the fact that the rack ceiling can hardly be called completely mirrored, it is considered the most popular. And all due to the fact that rack coatings are inexpensive, are characterized by a long service life, and are not afraid of moisture. In addition, damaged rails can be easily replaced with new ones without changing the ceiling completely.
Mirror polystyrene plates are the most difficult to install. They are plates with a self-adhesive back side. The main disadvantage of such a ceiling is the need for high-quality leveling of the surface. If slatted ceilings can be mounted on a surface with slight irregularities, then in the case of polystyrene boards, the ceiling must be perfectly even. In addition, when gluing the plates, you need to be very careful, and an assistant will not interfere. You need to glue evenly, because it will be very difficult to tear off already glued plates from the surface.
Suspended mirrored ceilings make it possible to hide communications (pipes, wiring) underneath. Their only drawback is their rather high cost.
Stretch mirror ceiling is a light thin film with a mirror surface. Such surfaces are not at all afraid of water, temperatures, do not fog up. In addition, if your neighbors suddenly flood, this ceiling will protect your bathroom from water penetration.
Mounting a slatted mirrored ceiling
As we have already said, the rack mirror ceiling in the bathroom is the most popular. It is about its installation that we will now talk about. The first thing to do is calculate the amount of material. At the same time, remember that you need to take a little more than you need, so you can always replace the spoiled material. There is nothing complicated here. The slats are sold in 4m lengths - just determine how many slats you need to cover the entire ceiling surface.
Don't forget to count the edge panels. Despite the fact that they most often need to be cut, the slats are considered as whole. The resulting number is the minimum required number of rails, and for reliability, as we said, take about 10% more of the total panels just in case. Installation work begins with markings for the end profile, the correctness of which must be checked using the building level. After mounting the end plans, we proceed to the installation of stringers that ensure the distribution of the load on the slats. Attach the stringers with self-tapping screws.
After that, we proceed to the installation of the panels themselves. The first bar must be mounted at a short distance from the edge of the walls, after which the rails are fixed to the stringers with a latch lock. Finishing rails also snap into place at the ends. At the last stage of work, they install, closing the remaining gaps between the walls and planks. That's all, the mirror ceiling in the bathroom from the slats is ready! It remains only to provide him with proper care so that the structure lasts as long as possible.
When it comes to repair, then, first of all, you need to choose the right finishing material. For renovations in the bathroom, only moisture-resistant materials are needed. No exception in this case and the ceiling plate. That is why designers unanimously advise giving preference to mirrored ceilings. This is explained by the fact that the basis of such ceilings is glass, for which neither moisture, nor temperature changes, nor constant steam pose a danger. In addition, there are other advantages of mirrored ceilings.
As a rule, the bathroom is one of the smallest rooms in a house or apartment, so the reflective effect of the ceiling can visually make the space larger. In such a simple way, you can create a doubling effect and it will seem that the room is at least twice as large. Therefore, most often such a ceiling is installed with a shortage of free space. It is also worth noting that the mirror solution will look very modern and original. The interior of the bathroom will look especially luxurious if it is made in black and white with silver decor.
Why choose a mirror finish?
If we compare all the ceiling decorations, then the mirror ceiling occupies one of the leading positions, as it is not only practical in everyday life, but also incredibly stylish. The main advantage of this design is that it is great for uneven or rough surfaces that require plastering. In addition, such ceilings have a number of other advantages.
mirror ceiling prices
mirror ceiling
The construction industry is developing rapidly, and finishing materials are being improved at the speed of light. Therefore, when looking for a design for the ceiling, you can find any version of the mirror surface that fully meets the needs of the consumer.
Note! If it was decided to install a mirror ceiling, then experts do not recommend doing this from a solid material. This is explained by the fact that glass is a heavy material, characterized, first of all, by fragility, so you should not take risks.
Slatted mirrored ceiling
This type of ceiling is obtained from aluminum slats with a mirror coating. You can choose aluminum profiles for every taste, as they exist in various color variations. At the same time, it is necessary to take into account the fact that the color of the profile should not contrast with the mirror coating itself. By its nature, a slatted ceiling, as a subspecies of mirrored ceilings, is not a mirror in the truest sense of the word, but despite this, it remains the most popular and sought-after option for decorating a ceiling slab in a bathroom.
It is easy to mount and does not require careful leveling of the surface. It is enough that the suspended beams are mounted on the ceiling, and to them, respectively, the slats. Mirror plates will be installed on them. Tellingly, here, if necessary, you can replace part of the coating, without having to dismantle the entire decorated ceiling.
Polystyrene boards
This is also one of the subspecies of the mirror ceiling design, which is a self-adhesive plate. Everything happens very quickly - the back base of the plate is attached to the ceiling plate with an adhesive surface. But not everything is as easy as it seems at first glance. First, the walls will need to be leveled so that the surface becomes perfectly flat. Such a coating is designed for rooms where the ceiling slab is finished with plasterboard.
Dropped ceilings
This type of mirror ceilings is very versatile. Thanks to this design, you can not only visually increase the space, but also hide communications. If, under any circumstances, one of the parts of the ceiling has become unusable, then due to the cassette structure it can be easily replaced without dismantling the entire ceiling. A false ceiling can bring more sophistication to the bathroom interior.
Stretch ceiling
Oddly enough, among the mirror ceiling coverings there is even such a view as stretch ceilings. They consist of a thin film the size of the entire ceiling slab. It is characteristic that this type is very popular among consumers. In combination with the right lighting, it looks very impressive.
Stretch ceiling prices
stretch ceiling
Naturally, such a ceiling will not have such reflective properties as an ordinary mirror, but only imitate mirroring. This is an ordinary glossy surface, which has an excellent gloss. The main advantage of such a ceiling is that when installed in the bathroom, its functionality increases and it never fogs up. On the contrary, a standard mirror ceiling after a long shower can be covered with water droplets, which will never happen with a stretch ceiling, which perfectly protects the main ceiling from moisture penetration.
Video - Installation of a mirror PVC stretch ceiling
How to install a mirror ceiling?
Installation of such a design of the ceiling consists of several stages. There is a huge variety of mirror ceilings and their subspecies, but not every one of them can be installed independently. For example, stretch ceilings require professional help. To install such a structure, metal frames are required, the installation of which occurs with certain skills and a set of knowledge.
It is extremely difficult to install solid glass materials. Most often, prefabricated slab structures are installed with their own hands. It is this process that is worth considering in more detail.
Stage number 1. Training.
Step 1. First of all, it is necessary to carry out preparatory procedures, which include leveling the surface. Thus, it will be much easier to install a mirror ceiling.
Step 2 At this stage, it is determined how many mirror plates will be required. Therefore, it is necessary to calculate the total area of the ceiling slab and divide this number by the size of the slab to be installed. As a result, you can decorate the ceiling without surpluses.
Advice! If the budget allows, then it is recommended to purchase finishing material with a margin. Since the installation takes place without the participation of specialists, deformations are possible during installation, which will inevitably lead to damage to the plate.
glass ceiling prices
glass ceiling
Step 3 If the material is in the form of a roll, then it must first be straightened so that the design lies on the surface as evenly as possible and looks aesthetically pleasing. For such manipulation, you will need any small weight with a soft base (to prevent scratching the mirror surface).
Step 4 Surface cleaning.
The work surface should be already prepared in advance. If not, the old coating is removed and the ceiling surface is polished. You can eliminate the presence of flaws and other defects with the help of plaster. If the irregularities of the ceiling slab are very serious, then it is best to use drywall.
Advice! When repairing the bathroom, it is necessary to use only moisture-resistant drywall. If you ignore this moment, then when you drink moisture, ordinary drywall will quickly deform and lead to damage to the mirror surface.
Stage number 2. Installation work
It is possible to carry out the installation in two ways - gluing or fastening with self-tapping screws.
Pasting a mirror finish
It is one of the easiest installation methods. It is recommended to apply on hemmed drywall or perfectly plastered surface.
Step 1. A special glue is applied to the ceiling and left for some time to dry. Thus, it is possible to improve the quality of the connection between the surface and the material.
Step 2 For better fastening, glue is also applied to the inside of the plate.
Step 3 After that, the material is attached to the surface of the ceiling.
Note! It is recommended to press the finishing material with a rubber roller.
Using self-tapping screws
Here, in the process of work, you will need attentiveness and, of course, accuracy in performing the action.
Step 1. First you need to make holes in each corner of the tile. This is done with a drill.
Step 2 Then rubber washers are mounted on the screws. This is done to prevent damage to the finish.
Step 3 After all the manipulations, the plate is applied to the ceiling surface and screwed.
Finally, you need to install chrome caps that will mask the rubber washers.
Installation of a mirror ceiling of the Armstrong system
Armstrong ceiling equipment
It is extremely difficult to install a suspended mirror ceiling on your own, especially if it is the Armstrong system. During installation, several difficult manipulations are required.
Calculation of the mirror ceiling "Armstrong"
Step 1. An open-type frame structure is assembled. It is necessary to create a frame from T-profiles (you will need transverse and longitudinal), L-profiles (namely, wall-mounted) and universal suspensions.
Step 2 It is necessary to mark the frame on the ceiling plate. Then the L-profile is fastened along the perimeter of the wall with the help of debels. With a step of 600 mm, suspensions are attached, on which the longitudinal profile will be suspended.
Prices for rack ceiling
rack ceiling
Step 3 The transverse profiles are inserted between the longitudinal ones into special notches. The result should be squares into which mirror plates are attached.
Thus, the installation of a mirror ceiling at home is not difficult.
Table. Advantages and disadvantages of mirror ceilings.
| pros | Minuses |
|---|---|
| Environmental friendliness and cleanliness. This criterion fully justifies the high cost of the material. Therefore, with constant contact with moisture, there will be no harmful fumes. | The material is quite expensive, so you need to be prepared for the fact that you will have to spend a lot of money on mirror design. |
| Mirrored stretch ceilings or slatted ceilings are durable and easy to install. | Mirrored ceilings are quite fragile material. |
| Almost all mirror plates can be installed independently. | Stretch ceilings require only professional installation. |
Ceiling panel prices
ceiling panels
Summing up
Decorating the bathroom ceiling with mirror tiles will be the highlight of the room and visually enlarge it. To create the perfect ceiling finish, you must adhere to all installation rules. And then you can get not only a beautiful ceiling, but also an environmentally friendly room. After all, mirror and glass ceilings are made mainly from natural materials.
Video - How to make a mirror ceiling with your own hands
Starting a bathroom renovation, many do not realize that this room has a number of specific requirements for finishing materials, room design and selection of furniture and headsets. So, when choosing materials, you need to remember that they must be with excellent water-repellent properties and appearance. Therefore, the repair of bathroom surfaces plays a crucial role and, in particular, the final result depends on the choice of ceiling covering. You can repair the ceiling surface with a huge amount of materials, but if you want to create a room with an exclusive design, you should pay attention to such finishing options as: glass and suspended mirror ceiling in the bathroom . Many will ask the question, “Why is this finishing option good?”, “What materials can I use to make a mirror surface?” and many more similar problems. Let's try to figure it out.
What material is suitable for a mirrored ceiling in the bathroom?
Despite all the variety of finishing materials, only those that meet the following requirements are suitable for repairing a mirrored ceiling in a bathroom:
- Resistance to the negative effects of moisture. Since sudden changes in temperature occur daily in the bathroom, the release of water vapor, ordinary finishing materials will quickly become unusable. But it should be remembered that not only facing materials must have special characteristics, but also fasteners and finishing mixtures. For example, drywall, profiles, putties and other ordinary materials without moisture resistant indicators cannot be used;
- Ease of maintenance and unhindered access. In order for a high-quality finish not to lose its original appearance for as long as possible, it will have to be looked after. Therefore, the mirror ceiling in your bathroom should be easy to clean and have free access to the surface;
- Minimum weight. To minimize the load on the base ceiling coating, you should select the lightest materials. Despite the fact that moisture has a negative effect on finishing materials, an additional load will accelerate the destruction process;
- Environmentally friendly coating. When choosing a finishing material for bathroom mirrored ceilings, you should pay attention to the manufacturer and price. That is, little or no unknown manufacturers, as well as cheap products, can be harmful to health and release toxic substances. It must be remembered that quality material is not cheap. Particular attention should be paid to materials such as: plastic, stretch films and other materials containing artificial resins;
Tip: If the selected finishing products have an unpleasant odor, you need to carefully check the quality and the attached documents for the material from the manufacturer;
- Ability to withstand significant temperature changes. The reason for frequent drops is hot steam and the operation of the hood, from which cool air enters. In this regard, abrupt changes negatively affect the durability of the material, it loses its appearance, and a favorable environment for mold and microorganisms contributes to rapid destruction. Therefore, you need to choose high-quality moisture-resistant materials, although they may be a little more expensive than usual, but they will last much longer.
Among all the above requirements for finishing materials, “real” mirror and glass ceilings for the bathroom have all the required qualities. That is, the surface is resistant to temperature changes and moisture, and pollution is easily removed and the most worthy quality is the environmental friendliness of the material.
Mirrored ceiling options
Despite the fact that it is considered to be a mirror coating of glass, but now there are a lot of finishing materials with a glossy reflective coating, which can be called "mirror" with confidence. And an accurate display of all the conditions in the room is not at all necessary. "What are the mirrored ceilings in the bathroom?"
Panel mirror ceiling made of aluminum rails
Another finishing material from which you get a mirror rack ceiling in the bathroom , is an aluminum panel. Due to its glossy finish, such a ceiling can rightfully be called a mirror, although the reflected environment will have blurry features, but the light fluxes are fully reflected.
For fastening, a special technology is used, which is similar to the frame for suspended ceilings, but here the panels are fixed in special longitudinal grooves. This method of installation provides easy installation and dismantling of panels if necessary.
Aluminum slats are produced in gold and silver tones, as well as with additional textures and images.
Among the disadvantages of the coating, one can note the difficulty in caring for the surface, especially with complex contamination. After all, when cleaning it is strictly forbidden to use aggressive detergents and powders with abrasives. As a result, the surface will become faded and ugly.
Stretch mirror ceilings
With the help of a stretch fabric, you can get a mirrored ceiling in the bathroom, although it is difficult to call it “real”. The reason for this is the properties of the tension web. It has a smooth glossy surface that can reflect light, but the display of objects and the interior is blurry. As the color of the film changes, the reflective qualities change, so the darker the glossy surface, the better objects in the room are visible. A light film reflects only light fluxes, interior details are almost invisible. Stretch ceiling is more elegant than "mirror".
Despite the imperfect "mirror" of the stretch ceiling, it is increasingly used in the bathroom and the reason for this is the ability to choose any color, pattern, 3D image, etc. Also, the canvas easily withstands specific operating conditions, and the simplicity of the design allows you to hide any errors premises. Due to the properties of the film, it can withstand the "floods" from the neighbors without spilling a single drop. And washing light dirt is not difficult, just a regular detergent and a soft sponge.
Among the disadvantages of such a ceiling, one can single out the high cost of the material, although a small bathroom will not cost very much. Also, over time, from frequent “floods” and high humidity, spots may appear on the surface, in which case you will have to change the stretch fabric completely. But this applies to light colors. Other than that, it's excellent material.
Suspended ceiling made of glass mirror plates
It does not matter which mirror or glass ceiling will be installed in the bathroom, the main thing is to use only proven methods of attaching panels to the ceiling. After all, not adhering to technology or an incorrectly chosen adhesive mixture can eventually lead to sad consequences. In this matter, you need to check all methods of fastening and pay special attention to the methods of installation that have been proven over the years.
Note! When installing panels directly to the base surface, it must be in perfect condition. That is, do not peel off, collapse and be perfectly smooth.
If you follow all the technological processes with mirror or glass panels, you can achieve stunning visual effects, while if the ceilings in the bathroom are low, this design will take a minimum of height and visually enlarge the room.
As a fastening frame for such ceilings, aluminum profiles are used, which are assembled into a rack structure and the end result is a cellular crate. Then the frame is sheathed with glass or mirror plates, the latter will display all the smallest details of the interior. Therefore, the quality of wall and floor finishes, as well as furniture and plumbing must be of high quality. Otherwise, an old bathroom or floor reflected in the ceiling will only spoil the whole design and the end result will only be disappointment.
If you want to achieve amazing results using glass mirror materials, you can use: corrugated, bevelled, engraved, rainbow effect, multi-colored and many other options for plates.
In order for suspended mirrored ceilings for the bathroom to have a chic look, you will have to think through the entire design of the room in detail, because the smallest flaws will certainly be reflected in the ceiling. If you want to achieve stunning lighting effects, you should use plates with beveled corners, in which the reverse light flux is reflected by rainbow rays. And the use of multi-colored or printed plates will help to realize any design fantasies.
Among the disadvantages of such a finish, one can note the high cost of mirrored glass plates and the need for careful maintenance, but otherwise it is an excellent environmentally friendly and durable material.
What is a good mirror and glass ceiling, its pros and cons
When choosing a ceiling finish for the renovation of any room in the house, it should be remembered that it does not matter what material will be used. They have their flaws and undeniable virtues. But you need to know about all the qualities.
So, the mirror and glass ceiling in the bathroom has such advantages as:
- Environmentally friendly and safe material. Using glass or mirror panels or plates, you can be sure of their safety, because they are made only from natural and environmentally friendly materials;
- visual effect. Due to their properties, mirror and glass materials visually enlarge the room and add light with a minimum set of lighting fixtures;
- Easy care. This method of finishing does not attract pollution, and mold and microbes do not multiply on the surface. Therefore, for cleaning, it is enough to use a regular detergent and a soft sponge. But be wary of using scouring powders or chemical cleaners;
- Surface preparation. A suspended mirror ceiling does not require a perfect base coat finish. The use of wireframe technology allows you to hide many surface imperfections;
- Ease of installation. Basically, the installation of glass and mirror ceilings is not difficult. The main thing is the correct installation technology. For a small bathroom, it is realistic to install a ceiling in a few hours.
The negative features of the mirror coating include the high cost of the material, the soiled surface and the fragility of finishing materials (except for tension and aluminum rails). But if you properly care for and eliminate shocks and other mechanical damage to the surface, then it will serve "faithfully" for decades.
Small Conclusions
The use of mirror and glass finishing materials in the bathroom can be the highlight of the room. The most important thing is to follow the rules for choosing and installing the material. This method of finishing is safe for health, because it is not subject to the aggressive environment of the room. But choosing this type of repair, you should choose a detailed design of the room. To facilitate the choice, you can see the photo and video reports of designers or reviews of other owners who have already carried out such repairs. The main thing is that they are not afraid to realize their design fantasies, because modern materials allow them to become a reality.
In an effort to make the interior impressive and stylish, many people resort to completely unusual materials and techniques.
Among the mass of interesting trendy design solutions, many owners are attracted by the idea of installing a mirrored ceiling in the bathroom. And absolutely not in vain.This design makes the room brighter, more spacious, "airy".
A mirrored ceiling is always an interesting move that gives any room a special charm. As for the bathroom, here it is not only highly aesthetic, but also very practical.
A well-mounted mirror ceiling structure has the following advantages:
- the maximum expansion of the internal space of the room (especially important for small rooms);
- visual appeal;
- moisture resistance;
- the possibility of arranging good uniform lighting of the room, increasing the efficiency of lamps;
- excellent compatibility with any interior due to the variety of materials used;
- functionality;
- wear resistance;
- hygiene;
- ease of care.
Among the shortcomings of mirrored ceilings in the bathroom, it is worth noting the excellent visibility of even small contaminants and the formation of stains when fogging.
But, if you do not forget about the timely cleaning of the surface and organize forced ventilation in the room, then these “problems” can not even be taken into account.
As for the cost of a mirrored ceiling in the bathroom, this pleasure is certainly not cheap. But its excellent appearance is definitely worth it!
Despite the rather high cost of mirrored ceilings, their popularity is steadily growing. This is the perfect solution for small bathrooms.
Types of reflective ceiling structures
Mirror ceilings are of different types. These include not only coatings made of real mirrors, but also other designs with a glossy surface that reflect light.
In particular, for the arrangement of mirrored ceilings in bathrooms can be used:
- solid mirror canvases;
- mirror tiles;
- polystyrene panels;
- aluminum (rarely steel) rails coated with reflective coating;
- glossy vinyl.
Modern technologies make it possible to produce mirrored ceilings of any color, with varying degrees of reflection, with a pattern or other decorative elements. Thanks to this, it is possible to create unique designs that fully satisfy the wishes of the customer.
One-piece mirror - a spectacular solution
Installing a solid mirror canvas on the ceiling in the bathroom gives the room a special luxury. The resulting surface looks incredibly impressive. True, such beauty requires considerable "victims" - both financial and physical.
Installation and subsequent operation of a ceiling structure with a solid overall mirror is associated with a number of difficulties:
- the fragility and dimensions of the material require the involvement of not just specialists in its installation, but mega-professionals with sufficient experience in carrying out such work;
- bringing in, unfolding and lifting up a whole mirror is quite problematic - the utmost accuracy of all persons involved in the process is required;
- even with the most careful installation, there will always be a risk of peeling and falling of the web. Needless to say, what danger can be fraught with such an incident?
Even a small “fragment” of the mirrored ceiling in the bathroom can, with the right lighting, transform the room, visually increase its volume.
If, despite all the difficulties, you plan to install the mirror on the ceiling with your own hands, follow this work technology:
- Carefully level the surface of the ceiling. A good result can be achieved both with the help of plaster, and by fastening GKL. In this case, it is better to install metal profiles for drywall sheets with a minimum step (20 cm) to eliminate the possibility of sagging of the structure.
- Prime the plaster, GKL does not need to be primed.
- Glue and be sure (!) Screw the mirror to the ceiling.
When mounting, use only special adhesives for mirrors. All other agents can corrode and spoil the amalgam of the mirror sheet. Glue must be applied in strict accordance with the manufacturer's instructions.
Lifting and installing a mirror sheet will definitely require several pairs of hands and reliable supports - keep this in mind.
It is better to entrust mirror drilling to its manufacturers. It is also better to consult with them about the number and location of the holes.
It is necessary to fasten the canvas to the ceiling plate or plasterboard with the help of special screws through plastic bushings. For aesthetics, fastener caps are recommended to be closed with decorative chrome caps.
Mirror tiles - stylish and individual
With the help of mirror tiles, the interior of the bathroom can be made truly impressive and unsurpassed. This is facilitated by a variety of shapes (square, hexagonal, diamond-shaped) and shades of the material.
The surface of the tile can be glossy, matte, tinted, with a pattern of any complexity.
The most popular color variations of mirror tiles are:
- Bronze. The pronounced golden color makes it somewhat difficult to detail the reflection. At the same time, such a surface has a unique effect of luxury, especially if the material is combined with other types of mirrors.
- Silver. Medium level of detail. Good reflection of light and objects, but without depth, brightness and sharpness.
- Graphite. Gray material with partial reflection. The resulting surface has a calm depth, with an annoying brightness in it.
A special attraction to the room, of course, will create a mirrored ceiling made of tiles with facet - a decorative bevel along the edge of the material. The refraction of light by the facet creates the effect of a brilliant shine.
Transportation and installation of mirror tiles require the same accuracy and care as in the case of a solid mirror sheet.
Installation is carried out according to a similar technology - after leveling the black ceiling, the material "sits" on the glue; if necessary, additional fixation of the tiles with screws is made.
There is no need to make gaps between tiles.
Temporary fixation of elements should be provided for the time of glue drying.
Mirror is a facing material with exemplary moisture resistance. It is absolutely not subject to the harmful effects of moisture and condensation. It really is a smart choice for a bathroom. However, the joints between tiles or panels can be very vulnerable. They must be treated with a silicone-based sealant. Fasteners must be stainless.
Polystyrene boards and their features
Polystyrene plates with a reflective film on top are the best solution for arranging a mirrored ceiling in the bathroom in cases where the lightness of the material and the ease of installation are more important than any other possible advantages.
This product is supplied in rolls; before installation, it needs to be "acclimatized" at room temperature, and (if necessary) to straighten out under load.
The ease of installation of a polystyrene ceiling is due to the presence of a “self-adhesive surface” on the reverse side, which ensures good adhesion of the material to the rough surface.
It is important to take care of the perfect evenness of the latter - so as not to end up with a "room of laughter".
The order of work during the installation of the material is usually as follows:
- Remove the protective film from the adhesive side.
- The plates are applied to the ceiling with a self-adhesive side and pressed down with force.
- The surface is rolled with a rubber roller to remove bubbles.
Sometimes mirrored polystyrene boards are offered without a self-adhesive layer - in such cases, PVA-based compounds are used to install the coating (for example, Henkel's Moment Installation).
When buying canvases for the bathroom, you must definitely pay attention to their purpose.
There are products intended for wet rooms, but there are also those that have a limited scope - contact with water is fraught for them.
Polystyrene mirror panels are not compatible with high power luminaires - keep this in mind when designing your interior.
In a very tiny bathroom, it is probably better to refuse a mirrored ceiling - in such conditions, the “well effect” is inevitable. The room will become uncomfortable.
Suspended mirror structures - simple and reliable
Quite popular are ceilings made of aluminum slats coated with reflective coating. Such structures are characterized by low weight, good strength and exemplary moisture resistance.
Aluminum slatted ceilings are completely fireproof; the temperature range that they are able to withstand is from -45 to +200 ° C.
The coating does not darken, does not turn yellow over time and does not corrode: you can safely choose them not only for the bathroom, but even for a bath, sauna or pool!
A huge advantage of these ceiling structures is also the minimum amount of dust during installation and the ability to install them at the final stage of repairing the premises.
It does not require the use of any building mixtures and preliminary surface preparation. Among the shortcomings of rack mirror structures, it is worth noting the distorted reflection.
In addition to slats, slabs of different sizes can be used to equip suspended ceilings with a reflective effect. It is convenient to mount separate mirror panels on Armstrong suspension systems.
The ceiling structure created using these guides is quite reliable and practical.
A large selection of colors and models of suspended mirrored ceilings allows you to safely experiment with the design of the room.
Mirror ceilings differ in the type of fastening, shape, color. A wide choice of materials allows you to design combined ceilings of two or more levels. Complex structures are recommended to be installed only in large bathrooms with long and wide ceilings.
Stretch mirror ceilings
You can create a "mirror effect" over your head in the bathroom by installing a stretch ceiling made of vinyl film with a glossy texture.
The resulting reflection will certainly be fuzzy, with slightly blurred contours, but it will look very natural and harmonious in the interior.
The main advantage of glossy stretch ceilings is the ability to create unique multi-level structures with their help. A wide choice of shades of the reflective surface allows this material to successfully "introduce" into the interior.
A stretch ceiling is a good solution for a bathroom both from an aesthetic and practical point of view. It is not only beautiful, but also durable, hygienic, unpretentious in care.
And even able to protect against flooding. The film simply stretches and sags under the weight of the liquid. It is enough to drain the water correctly - and you can forget about the emergency.
It is not recommended to install mirrored stretch ceilings on your own. The process of their installation requires the master not only to have knowledge, skills and rich practical experience, but also special equipment.
A glossy stretch ceiling is one of the most practical solutions for arranging a surface with a reflective effect. True, he certainly cannot be compared with the splendor of real mirrors.
Important operational details
Is it still worth doing a mirrored ceiling in the bathroom? If you like this solution, then it is definitely worth it. The aesthetic qualities of mirror structures are always on top, they also do not hold up to functionality and practicality.
A wide choice of materials allows you to equip reflective ceilings with any financial possibilities and harmoniously “integrate” them into any of the interior styles.
When installing a mirrored ceiling in the bathroom, it is very important to pay sufficient attention to the issue of lighting - to determine the type, location and number of lamps.
A lot of lighting fixtures in a bathroom with a mirrored ceiling are definitely not needed, since the reflective surface can enhance the level of illumination of the room.
When installing spotlights, it is imperative to take into account the presence of patterns and other decorative elements (if any) on the mirror: their incorrect location can hopelessly spoil the expected visual effect.
As for the care of the mirror ceiling, it is worth noting that he does not tolerate careless handling. Fingerprints, stains from a damp cloth, scratches and chips on it are very clearly visible.
Cleaning of such a coating should be carried out exclusively with a damp sponge and a mild soapy solution or special products. No solutions containing aggressive substances.
After cleaning, thoroughly dry the surface with a soft cloth in a circular motion. This will ensure that the ceiling is perfectly clean and the light is evenly reflected.
With the right selection of materials and proper installation of the structure, a mirrored ceiling is a sheer practical and aesthetic pleasure.
The desire to make the living space unique pushes us to search for extraordinary solutions for interior design. The mirrored ceiling in the bathroom is one example of thinking outside the box.
This approach guarantees not only a visual expansion of the space, but also demonstrates a bold design solution that takes the design of the entire bathroom to a new level. Reviews on the installed mirror ceiling in the bathroom are exceptionally enthusiastic.
Installing a mirrored ceiling in the bathroom is quite possible for people with different levels of security. There are economy options and there are super expensive, luxurious designs.
Economy options for mirrored ceilings
Inexpensive mirror ceilings perfectly imitate a mirror thanks to a special coating that can reflect light very effectively. The cost of 1 square meter of such ceilings ranges from $15 to $55.
This group includes ceilings:
- Stretch vinyl
- Mirror rack
Stretch vinyl ceilings
A very popular type of mirror ceiling. Its undoubted advantage is a wide choice of color shades of the reflective surface. The stretch mirror ceiling in the bathroom looks most advantageous in combination with its other types. Especially, with multi-level ceilings, assembled from moisture-resistant gypsum boards.
The mirror effect is mainly provided by the glossy surfaces of stretch ceilings. Darker shades increase the reflectivity of the vinyl. To maximize the reflection of light, manufacturers produce vinyl films with an additional layer, which greatly enhances the imitation of a mirror.
Installation of a mirrored vinyl ceiling does not differ from the usual installation of a stretch one:
- Along the perimeter of the room, at the level of the planned ceiling, special plastic or aluminum baguettes are placed
- Vinyl is heated with warm air to increase its elasticity.
- The surface of the stretch ceiling is straightened, the seams are aligned and filled into baguettes
- After the vinyl has cooled, it will stretch, become elastic and only under warranty will last at least 10 years.
But no matter how hard the manufacturers try, it is not possible to achieve the absolute effect of a mirror in this version. There is a slight blurring of the lines in the reflection.
Stretch mirror ceiling
Mirror rack ceiling
Rails for a suspended mirror ceiling are made of aluminum. To obtain a reflective effect, a chrome layer is applied to the panels and carefully polished. The quality is such that mirrored slatted bathroom ceilings are very difficult to distinguish from real mirrors.
Installation of a mirror rack ceiling
A very simple and quick assembly of a rack ceiling can be done even by a non-professional. Manufacturers have created an excellent designer, according to the clear instructions of which the suspended ceiling is assembled.
Brief description of the assembly process:
- We make the markup of the future ceiling
- We fix wall corners
- We hang guides for rails - traverses
- We mount on them rails with a mirror coating
Naturally, when assembling, do not forget about lighting, which, with a mirror effect, is better to mount on rails.
The view of such a ceiling is great, but there are still minor flaws in the reflection.
Mirror rack ceiling
The splendor of the mirror on the ceiling
A real, not imitating, mirror ceiling in the bathroom is a source of increased and pleasant mood at every bath or shower.
The mirror is a polished glass with a thickness of 3 - 7 mm, with the thinnest coating of silver, bronze, titanium or, in a particularly expensive version, gold, applied on one side. Unique combinations of coatings are possible, which can give the mirror a colored reflection. The type of coating changes the shade of the mirror, but does not reduce its reflective characteristics. Silver plating is the most common.
The processing of its edge at an angle of up to 45 degrees helps to maximize the beauty of the mirror. This finish is called facet. The ceiling of beveled mirrors is breathtaking with its beauty and completeness of forms.
Beveled mirrors on bathroom ceiling
The ceiling design solution can leave the minimal joints between the mirrors open or hide them under decorative narrow strips.
Placing mirrors on the ceiling in the bathroom guarantees a full 100% reflection of light, but also significantly increases the requirements for personal safety. Mirrors are a rather heavy finishing material that requires a very reliable fixation. Especially when it comes to the ceiling in the bathroom.
Types of mounting mirrors on the bathroom ceiling
When working with a mirror, precautions must be taken. The glass from which the mirror is made is a very fragile material.
Important! Accidental breakage produces sharp edges that can cause deep cutting wounds.
In almost all types of ceiling installation, you will have to deal with cutting. The mirror must be cut on a perfectly flat surface with a glass cutter, which must be dipped in kerosene immediately before the process. The cut will be perfectly even.
Holes for lighting elements are drilled with a diamond-coated core drill. To obtain technological holes of small diameter, special glass drills with diamond coating are used.
There are three options for implementing the idea of \u200b\u200bthe ceiling of mirrors:
- Fasteners based on special glue
- With dowels and screws with rubber seals
- Suspended ceiling kits from manufacturers
Adhesive connection
The first option is only at first glance very simple. In fact, it involves the ideal preparation of the site for gluing the mirror. It should be as smooth and durable as possible. Often it is necessary, first, to mount a reliable suspended structure.
Important! It is forbidden to stick mirrors on the plaster layer. Adhesive installation must be carried out directly either on a concrete floor, or on a moisture-resistant gypsum board, or on moisture-resistant plywood.
In the wall mounting of a mirror, glue is applied to its inner surface, around the perimeter and criss-cross. When attaching the mirror to the ceiling, it is advisable to apply glue along the perimeter and in zigzags along the entire remaining inner plane. In this option, there is no threat of collapse of large pieces of the mirror if it is accidentally damaged, which could cause injury.
Important! In branded false ceiling designs, mirrors are used, with protective films applied to them from the inside, which can hold all the fragments on themselves in the event of a destructive blow. There is a complete analogy with car windows.
A significant advantage of the adhesive method is the ability to safely mount very large mirrors on the ceiling.
Fixing the mirror with dowels
Installing mirrors on the ceiling with dowels is reliable and easy. Due to the large weight of the mirrors, in this type of installation, their small dimensions are used. The maximum side length must not exceed 60 cm.
As a rule, holes for fasteners are drilled at the corners of the mirrors. Under the screws of the dowels, rubber gaskets must be placed, and the dowel caps are closed with decorative overlays.
This method has an advantage. There is no need to install a suspended structure and perfectly align the ceiling. The horizontal level of the entire ceiling is leveled by the degree of screw tightening.
If the base ceiling is even, then a combined adhesive connection with dowels is used along the edges of the mirror.
Branded suspended structures
Well-known building brands Albes (Russia), Geipel (Germany), Donn (Germany), Armstrong (England) offer various ready-made sets of suspended mirror ceilings.
Suspended mirror ceiling Albes (Russia)
Kits are an elementary constructor. It is not difficult to assemble a suspended mirrored ceiling in the bathroom on your own, without the involvement of specialists.
The advantages of purchasing a suspended mirror ceiling from companies with a professional approach are obvious:
- Complete ceiling kit
- Simplicity and ease of installation
- Gorgeous, thoughtful design
- Guarantees for safe operation
All load-bearing and fastening elements of T-15 and T-24 suspension systems for a mirrored ceiling are made of either aluminum or galvanized iron.
15 and 24 are the width in millimeters of the decorative coating of the profiles visible from below, which can have a color:
- gold
- matte gold
- chrome
- crimson
- black matt
- silver
- white
The main element of the ceiling in the bathroom is a mirror. Manufacturers offer its various sizes and shades of colors.
Mirror plates in sets are supplied in the following sizes:
- 292mm*295mm
- 395mm*395mm
- 495mm*495mm
- 595mm*595mm
- 295mm*595mm
- 295mm*895mm
- 895mm*895mm
- 1195mm*1195mm
The following color shades of mirrors are offered:
- Colorless (standard silver plating)
- Bronze
- Pink
- Toned
- Grey
- Blue
- Green
- Antique
There are two main directions for mounting a mirrored ceiling in the bathroom:
- Diagonal of the room
- Parallel to the walls
The first option looks preferable, but involves a much larger number of mirror cuts.
If the choice is made in favor of the direction of the mirrors in the bathroom parallel to the walls, then installation must begin from the far wall from the front door. Shortened mirrors in this case will be located near the entrance and will be visually less noticeable.
Scheme of installation of suspended mirror ceiling system
Installing a mirror ceiling in the bathroom:
- We prepare the subceiling space. We clean it from peeling of plaster and paint, primer
- We mark up the future stream
- We fix a decorative corner on the walls
- We mount the supporting structure of connecting and transverse profiles and fix it with brackets on the ceiling
- We cut the mirrors extreme to the walls, drill holes for the lamps
- First we lay mirrors with holes for future lighting elements
- Installing lighting fixtures
- We place all other mirrors on the structure
Ceiling installation completed.
The price of a mirrored ceiling in the bathroom, depending on the design, ranges from $40 to $150 per square meter.
The mirror ceiling in the bathroom is not afraid of moisture, it is completely environmentally friendly, it looks amazing and brings the overall design of the room to perfection.
Loading...