Which door to put in the bathroom: choose the best option. Doors to the bathroom: choose a model and material (photo selection) Which doors are suitable for the bathroom

What door to put in the bathroom so that it does not deteriorate from high humidity, is durable, reliable and beautiful? Not every material will be able to withstand the specific conditions of service without consequences, so it would be impractical to choose a door, guided only by its compliance with the interior. Let's figure out which doors are better to put in the bathroom according to the type of construction, material and external design.

Wood MDF Plastic
Glass Mirror Stained Glass

To withstand the operating conditions in the bathroom, the door to the bathroom must be resistant to high temperatures and humidity, provide good air exchange and sound insulation, and have antiseptic properties. What materials will meet these high requirements?

natural wood

Solid wood bathroom door is a good choice if it meets the following requirements:

has an external water-repellent coating of paint or varnish;
treated with antiseptics;
made of hardwoods that absorb moisture poorly (beech, oak, mahogany).

It is important to properly install the door unit. So that the box does not warp over time from constant exposure to hot steam and water, it is fixed using anchors and mounting foam. If these conditions were met during selection and installation, its further durability will depend on proper care. From constant humidity and evaporation, the outer protective coating loses its properties, and it must be updated from time to time, otherwise cracks may appear on the canvas.

Covering from MDF or fiberboard

Manufacturers of doors made of MDF and chipboard assure that the products are absolutely not afraid of moisture. In fact, the construction consists of a frame made of pine, which is characterized by high hygroscopicity. The design has water-repellent properties due to the outer finish of the canvas: the laminated coating is resistant to moisture, but until chips and scratches appear on the surface. There are other vulnerabilities: the back of the box, for which water-repellent protection is not provided. In just a few days of operation, the wood can swell, and the door will no longer close completely.

Products made of MDF and chipboard have an affordable cost, a wide range of models and a variety of colors - these are their main advantages. To ensure their long service life, it is necessary to treat all open areas of the box with a protective compound, make sure that the edge of the leaf is glued with high quality and has no gaps, and protect the surface of the door from damage.

metal-plastic

If you are going to purchase doors to the bathroom and toilet, and doubt which ones will last better and longer, take a closer look at metal-plastic structures. Aluminum and plastic, the main components of these doors, have a lot of advantages:

resistance to moisture, temperature changes and cleaning agents;
strength and durability;
resistance to deformation;
simple hygiene care;
lack of a nutrient medium for putrefactive bacteria and fungi;
low cost.

Choosing a door to the bathroom with a design similar to other designs installed in the apartment will also not be difficult: the exterior decor of metal-plastic PVC film allows you to get any color and texture.

Glass

Glass door - very good an option for the bathroom, given the resistance of this material to moisture. There will be many disadvantages of such a design:

When hot water is turned on, the glass surface is constantly covered with condensate. Moisture flows down the smooth panel, accumulates in puddles on the floor and leaves stains.
Water stains, splashes, fingerprints are very clearly visible on the glass surface, therefore, such doors need constant hygienic care.
Glass is a fragile material, and if it is broken, it is also dangerous. So that in case of damage to the glass door it does not crumble into small fragments, the surface is protected with a special film, and this affects the increased cost of products.
The low level of sound absorption is another drawback.

The design of glass doors is very diverse. It is customary to install deaf structures in the bathroom, so designers solve the issue of glass transparency in various ways: they create stained glass drawings, spray paint, paste over with a film or matte.

Types of doors by opening method

Swing Sliding Folding

What is the best door to put in the bathroom according to the method of opening? Manufacturers provide several designs to choose from.

A swing door is the usual standard option, quite convenient, if only square meters allow. The design consists of a box and a sash attached to it with hinges. Provided that the bathroom is usually modest in size, the door leaf opens outward. This saves space in the bathroom. It is necessary to install such a door taking into account that it does not block free access to other rooms in the open state.
A sliding door does not require additional space in the room, but for it it is necessary to leave a free part of the wall where the sash will move. There is another option: equip a groove inside the wall where the sash will go when opened. In this case, the door will not interfere with the use of free space.
The folding design "book" or "accordion" has the only drawback - poor sound insulation. This design is compact and takes up minimal space when opened.

Color selection

What color to choose doors for the bathroom and toilet? The entrance to the bathroom, kitchen and rooms is usually located in the hallway. To avoid color dissonance, the most rational solution is to choose the same shade for all designs. If the door block delivered to the bathroom is made of a different material, care must be taken in advance so that the decor of the doors harmonizes in color with the interior. It can be a colored textured PVC film, a similar pattern on glass and similar fittings.

Hardware Features

Choosing the door to the bathroom, you need to take care of suitable fittings. These are hinges and a latch handle. It is desirable that the design of the chosen option matches the fittings installed on other doors of the apartment. To check the quality of products, you should pay attention to the following points:

Door hinges should not creak. High-quality fittings open smoothly, but with little effort.
A lock with a magnetic latch has a shorter service life compared to a mechanical one. Pay attention to the tongue of the lock. A plastic tongue creates less noise when closing than a metal one.
You can determine the quality of a door handle by its weight. The iron core, which is characterized by a long service life, is much heavier than the unreliable silumin - the material for cheap Chinese products. The handle spring must be elastic.
In order for the door to be locked from the inside, the handle must have a locking device. More reliable in operation is the option when the latch is included in the handle kit, but is located separately during installation.

All door hardware should be covered by a warranty. If the store refuses to issue a warranty card, it is better to refrain from buying.

Rating of manufacturers

Before choosing the doors to the bathroom and toilet, we suggest that you familiarize yourself with the rating of manufacturers.

"Alexandria Doors"- Ulyanovsk factory. Modern equipment from Germany and Italy allows us to produce products of European quality.
"Volkhovets". The doors of this brand are produced in Veliky Novgorod. Buyers are provided with a very wide range of products in a variety of styles.
"Dera". For more than twenty years, the Penza company has been producing its products. The manufacturer offers a unique design, high quality and affordable prices.
"Stendor"- practical, elegant, durable doors from St. Petersburg. The factory is equipped with imported equipment.
"Sophia". The Tver factory recently upgraded its equipment. Products are made in accordance with international standards.

World famous foreign brands:

Tre Piu is an Italian company. It offers non-trivial models with finishing elements made of aluminum, impact-resistant glass, veneer, precious woods.
Garofoli- a huge range of models from the Italian manufacturer.
Dana is an Austrian company. It has been supplying its products to the world market for over 40 years.

Products of well-known manufacturers are characterized by decent quality. The durability of the product depends not only on how to choose a door, from what material, and from which manufacturer, but also on the correct installation work, timely hygienic care and careful handling.

The bathroom and toilet are rooms in which there is a characteristic microclimate. High humidity, temperature changes are factors that adversely affect the interior door leaf. Therefore, we often ask ourselves: which door to put in the bathroom? At the same time, I want the product to last a long time and maintain an aesthetic appearance. In addition to these criteria, the combination of an interior product with the style of the room and the apartment as a whole is considered important.

Choice of bathroom door material

The decisive factor in deciding which doors are better to put in the bathroom is the area of \u200b\u200bthe sanitary unit. The level of air humidity directly depends on this criterion. In a small room, the humidity level will be high. This factor will be exacerbated if the ventilation in the room is either absent or weak.

If you are thinking about which door is better to install in the bathroom, you can choose from the following options:

wood or wood veneer;
polymer-coated doors (laminated, with PVC film, covered with eco-veneer);
plastic models;
glass products.

Each of the materials or types of product coatings is characterized by its pros and cons.

What criteria should be followed when choosing?

In the question of which doors are placed in the bathroom, consultants recommend focusing on the characteristics of the bathroom. If the humidity level in the room exceeds 60%, experts recommend paying attention to materials that are alternative to traditional wood and the usual wood derivatives. In this case, it is better to give preference to plastic and glass. If the room has a large area, is equipped with sound ventilation, then you can install solid wood doors, veneered, laminated or enameled.

Of great importance in the question of which door to put in the bathroom is the type of protective coating applied to the door leaf and edge. In the manufacture of some models, the following technology is used: the film is applied first to the canvas, and then to the edge. A joint imperceptible to the eye is formed, and if it is leaky, then moisture will penetrate in this place and the canvas will deteriorate over time.

When making a door from a hygroscopic material (wood and its derivatives), the upper and lower ends are usually not covered with a moisture-proof film. These weak areas will attract and store moisture from the bathroom. When choosing doors to the bathroom made of wood, they must be covered with a hydrophobic varnish without fail.

Laminated products

Affordable, they are made from a base and paper glued to it by means of resin. The coating of poor quality is easily damaged and moisture penetrates in places of damage. Laminatin has the best consumer characteristics. It has a large layer thickness and is varnished in several layers. The cost of such a product is higher than laminated counterparts, but laminate interior doors are durable and withstand humidity of 60% or more.

PVC Coated Models

The frame of such products is made of MDF coated with PVC film. The coating gives the door water-repellent properties, so they can be washed with the use of sanitizers. A big advantage of such products over plastic counterparts is a wide range of colors and textures. The disadvantages include the possibility of delamination of the fabric with subsequent ingress of moisture into the structure, as well as the presence of chloride in the composition of the film in small quantities. If choosing a bathroom door is a safety aspect for you, then avoid buying products with PVC film. At elevated temperatures, chloride is released into the environment, so the PVC coating is not environmentally friendly.

Eco veneer doors

Eco-veneer is a new generation bathroom material, a product of the fusion of woodworking industry waste and polymeric plasticizer. The latter is harmless and environmentally friendly. On the outside, the eco-veneer is indistinguishable from natural material. However, in terms of consumer qualities, eco-friendly veneer is superior to natural veneer. It is resistant to moisture and mechanical impact, aesthetic and does not emit harmful substances into the atmosphere even at elevated temperatures, it is well suited for the bathroom. The only downside is poor soundproofing.

Wood or veneer products

Wooden products are rarely installed in bathrooms due to their high hygroscopicity. However, if there is a coating of good varnish, paint, these models can last for decades.

The frame of the doors with veneer trim is made from inexpensive (soft) wood or chipboard, and the exterior trim is made with a thin cut of valuable varieties. Veneered products look very respectable, but they are not resistant to moisture. Therefore, if the level of humidity in the room is high, then it is not recommended to install models with veneer trim.

Plastic doors

They are affordable because they are made from inexpensive raw materials. The cavities of the product are filled with expanded polystyrene. Plastic models are absolutely hydrophobic, not afraid of temperature changes, biological effects of fungus and mold. In addition to these advantages, plastic doors provide good sound insulation and prevent heat transfer.

The disadvantages of these products are their uniformity and unrespectable appearance. Basically, interior doors made of plastic are made in a standard shape, size and painted white. In addition, when in contact with high temperatures, plastic begins to release chloride, which is why it is considered an environmentally unsafe material.

glass models

They offer the highest performance and are ideal for installation in the bathroom. Glass doors look unusually beautiful, give the room lightness and increase space. Modern tempered glass or triplex is not afraid of mechanical impacts, they can be washed using chemicals. If you are in doubt about which door to install in the bathroom, give preference to this material.

Glass is absolutely safe from an environmental point of view and a good material, and new technologies for the production of products from this raw material exclude the possibility of injury from fragments. Even with a strong blow, the door will not shatter into fragments, you will only see a network of cracks inside the polymer film. The disadvantage of a glass interior door is its high cost and heavy weight, which means forcing the opening and choosing durable fittings. For aesthetic reasons, frosted glass models should be chosen in the bathroom.

What are the best doors for bathrooms?

From the abundance of models of interior doors, it is sometimes very difficult to make a choice. The comparative characteristics of various products presented in the table will help you decide which doors are best for the bathroom:

Evaluation criterion	door type
	Wooden	Glass (tempered glass and triplex)	Plastic	Coating type
	Wooden	Glass (tempered glass and triplex)	Plastic
moisture resistance						High with full coverage
Temperature resistance					Excellent
Resistance to mechanical wear
Appearance	Respectable	Respectable	unrespectable	unrespectable	Respectable	unrespectable	Respectable

Noise and soundproofing	Excellent		Excellent
Environmental friendliness, safety	Excellent	Excellent		Excellent	Excellent		Excellent
				Affordable	Affordable	Affordable	Affordable

Conclusion

When deciding which doors to put in the bathroom, you need to decide which of the criteria is most important: respectable appearance, moisture resistance, resistance to mechanical wear. Glass doors are a versatile option. They meet all the criteria, but have a lot of weight and cost. More budget options are doors coated with eco-veneer, laminate, veneer. Plastic doors and PVC-coated products have a potential health hazard as chlorine is released in hot environments. Wooden products are not recommended for installation in rooms with a humidity level above 60%.

Are you going to put new doors in the bathroom and toilet? The choice of products must be taken very seriously so that you do not have to change them in just a couple of years. Let's find out what designs are suitable for these rooms.

When buying a door to a bathroom or toilet, you need to remember the most important thing - these rooms are characterized by high humidity. The humidity level will always be higher than in other rooms even when a powerful ventilation system is installed.

Glass products can be placed in the toilet and bathroom. If we are talking about moisture resistance, then such products are considered the best. And all because the glass is not afraid of delamination under the influence of high temperatures. Also, glass is a hygienic, environmentally friendly material, characterized by a good level of heat and sound insulation. At the same time, doors intended for installation in a bathroom or toilet are made of tempered glass, with a high level of strength. Therefore, it is quite difficult to break them. Other advantages include their stylish and elegant design.

Glass product for bathroom and toilet

The surface of products can be any: tinted, embossed, with a mirror finish. And expensive models are produced with inserts made of natural wood, metal, mosaics. And thanks to the "light" design of the doors, the space in the room visually increases, the bathroom will look wider and brighter. The downside of such products is the rather high cost and the need to frequently wipe the glass surface to remove fingerprints, dust and other contaminants that are very visible on this material.

The second popular option is plastic doors. Such structures are not afraid of moisture, do not deform as a result of exposure to hot temperatures. They are also characterized by hygiene, ease of use, low weight. PVC products are available in a variety of colors, making it easy to match them to the design of your bathroom or toilet. Despite the fact that in terms of their aesthetic properties, such products lose to glass doors or wood products, they are very popular. And all thanks to the affordable price.

In the bathroom and toilet, you can put a door made of natural wood. Many do not dare to buy structures made of natural wood, which is afraid of moisture, believing that such material is more suitable for. However, modern manufacturers have been able to solve this problem by offering reliable structures made of beech or other wood species.

Before selling, products are treated with powerful antiseptic solutions and varnished, which protects the material from the negative effects of moisture.

Lacquered natural wood door

True, there is one caveat - it is better if the door opening is located away from the steam and water supply devices in order to reduce the risk of deformation. The only disadvantage of such products can be called their high cost. For the bathroom, you can choose laminated structures made of MDF (chipboard). Such products perfectly "live" in a humid environment, are attractive in appearance and are inexpensive. But it is better not to put models made of natural veneer in the bathroom, since the thin material will not be able to withstand contact with moist air for a long time.

Having chosen which door you will install, do not forget about fittings and other elements. So, a very large load is placed on the hinges, the handle and the locking mechanism of the door as a result of the humidity in the room. Therefore, you should not save on fittings by choosing trusted companies, even if it will be more expensive. Products must be coated with an anti-corrosion compound. You can choose from stainless steel hardware.

Before putting the door in the bathroom or bathroom, you need to study some of the installation features. So, the doorway in such rooms should be equipped with a threshold about 5 cm high, which will protect the apartment in case of flooding. Therefore, bathroom doors are always installed higher than other interior doors - the difference can be about 10 cm.

Often, apartment owners purchase the same type of product for all rooms. However, a standard sanitary cubicle usually has a doorway height of about 1.9 meters, the height of the doors is about 2 meters. In this case, you will have to adapt the doorway to install a higher door leaf than calculated. When thinking about which doors to install, do not forget about the thinness of the walls in the bathroom - usually their width is about 5 cm. Therefore, when choosing a design, you need to take into account the width and dimensions of the door frame. It is better if the width of the box exceeds the width of the walls by no more than 2 cm, which are necessary for a layer of cement and tiles.

Bathroom door installation

If the box is wider, you will have only two options:

thicken the wall in the bathroom;
cut off a couple of centimeters from the box.

True, and here there is one nuance. If you have chosen MDF doors for the toilet, cutting off “extra” centimeters from the door frame is not recommended - this can lead to flaking of the material, due to which the door will simply lose its appearance.

In the interior, an important factor is the method of opening the door. But at the same time, you should not forget about functionality. If you choose the wrong door leaf, you can make the room uncomfortable. Swing structures are usually installed in the bathroom and toilet. Their main advantage is that they help to well isolate the rest of the rooms from moisture and excess noise. Such products are considered the most reliable.

Swing door design

Popular in the interior are and. Their main advantage is a significant saving of space in the room. But there are a few "buts" regarding their installation in the bathroom. First of all, such products will not provide 100% insulation of the room, the same applies to humid air. The second caveat is that cheap models of this design begin to “rattle” in a couple of years. Well, it should be noted the difficulties with their installation - you are unlikely to be able to carry out the work yourself.

High humidity and temperature, splashes of water and soap suds - not only the floor and walls in the bathroom are exposed to all these aggressive influences. The bathroom door is also under threat - meanwhile, special models are rarely found in manufacturers' catalogs with photos. In such cases, it remains to buy ordinary serial products - this will also help to create. Indeed, according to modern design canons, doors should be the same or designed in the same style.

Which door is best for the bathroom

When developing technology, most manufacturers take into account that their products will be used, including in wet rooms. However, this does not mean that any of the models on the market is suitable for a wet area. We tell you what to look for when choosing.

Which material is best for bathroom and toilet door

First, consider what materials are generally used.

Lamination

It is produced as a base and a layer of paper glued to it - this is called the lamination process. But they are not glued to ordinary glue, but with the help of special resins. But still there are gaps into which moisture can penetrate. Perhaps one of the few options devoid of this drawback is laminatin. It is thicker and varnished on top for better protection. Fabrics treated in this way can withstand humidity up to 60%.

PVC coating

Such models have an MDF base, and a PVC coating on top. It is water repellent and can even be washed. The advantages include a wide variety of colors and textures of these interior doors - it will be easy to choose the one you like for the bathroom and toilet. But there are also disadvantages - the canvas can exfoliate from too high humidity. And when the temperature rises in the paving, PVC can release chloride - for those who strive for it, it is better to abandon this type.

Ecoveneer

A modern material that is produced from woodworking waste and polymeric plasticizer. Despite the complicated name of the latter, it is environmentally friendly. Eco-veneer is difficult to distinguish from natural material externally, but it even surpasses real veneer in quality. Among the advantages are resistance to moisture, aesthetics and environmental friendliness. But it can become an argument not in his favor.

Wood (veneer)

Too capricious, and is unlikely to show itself well in the bathroom. But if you choose a product coated with high-quality varnish, it is quite possible to install it. The frame of veneer products is made of softwood or chipboard, but the outer side is already covered with natural wood.

Plastic

Perhaps, if you are looking for an answer to the question of which door to put in the bathroom and save the budget, this is exactly your option. Raw materials are inexpensive, so the finished product is available. Plastic is not afraid of temperature changes or moisture, as well. And the sound insulation of such models, as a rule, is on top.

But do not rush to draw an unambiguous conclusion - especially if aesthetics are important to you. Plastic products are rarely beautiful, and they are also made in a standard form, and any deviations are impossible. Also, it is not eco-friendly.

Glass

Glass structures are absolutely waterproof, but the thickness of the canvas must be at least 8 mm, otherwise it will not be possible to provide sound insulation. In addition, you need to take into account that products decorated with sandblasting (matte and with a matte pattern) become transparent when moistened, and any relief pattern (laser engraving, fusing) will greatly complicate surface care.

It is better to give preference to hardened structures with a colored ceramic coating or triplex - plain color, with a pattern or photo printing. Glass products will last longer in the bathroom than any other, while it is easy to choose the option that matches the style of the apartment.

So which material is the best? Pay attention to alternatives to wood: eco-veneer, plastic and glass. And only if the room is spacious enough and well ventilated, you can think about laminated, natural wood (veneer) and PVC-coated. When choosing the latter, the type of coating on the web and edge is of great importance. If the joints are not tight, moisture will penetrate in this place and the product will deteriorate.

Which door to choose in the bathroom by design

There are traditional options - swing and other designs. Let's consider each.

swing

A classic that is used in all rooms. It has a standard frame: a box, platbands are placed. You can also put thresholds, and this improves sound insulation. The standard swing type opens inward or outward, and there must be room for this. If inside - there may be problems with this.

sliding

The design of the coupe is very space-saving, which again is useful in small spaces. But during installation, a gap remains between the floor and the canvas, which means that heat and sound insulation will be reduced.

You can compromise and install a model that slides into the wall - this is possible only before the start of capital work, since it will be necessary to ditch the wall. With such sliding options, the disadvantages are minimized.

folding

Structurally divided into a book and an accordion. In the first case, the canvas is divided into two parts, and in the second - into three or more. When folded, they take up space in the opening, so the space savings are essentially negligible.

6 things to consider before buying

1. The presence of decor

Paneled structures are made from solid wood, according to the generally accepted opinion, they are unsuitable for a bathroom. However, this is not always true. If the frame of the structure is made of glued beams, and the panels are made of high-density fibreboard (HDF), and at the same time the canvas has a multi-layer coating (high-quality polymer enamel or varnish), then water is unaffected by it. The likelihood of warping and cracking is minimal, and the finish will withstand both high humidity and frequent washing.

And shield (smooth) canvases, as practice shows, are quite capable of withstanding the conditions of the “home tropics”. Such models are distinguished by stable geometry, because their frame (usually made of ordinary coniferous bars) is protected from moisture by sheathing. But the service life of the latter depends on the type of decorative coating.

2. Transparency

The presence of frosted or tinted glass often raises questions. From an aesthetic point of view, it looks nice and good, but how practical and is it suitable for a bathroom? The fact is that sound insulation is good only if the glass is dense, from several layers.

3. Size selection

Usually the bathroom and toilet should be about 194-196 cm in height and 60 cm in width. Meanwhile, the minimum standard for the height of the door block for many companies is 204 cm. The design of the required dimensions can be made to order (it will cost 10–20% more, and it will hardly be delivered earlier than in 2 weeks). Another option is to file the canvas, after checking with the manufacturer how to do it correctly. Usually, 100 mm can be cut off from panel sheets both from below and from above, but then a strapping bar should be glued in place.

There is always an extractor fan in the bathroom. Moreover, in many apartments it is designed to serve adjacent premises. And it will function normally only if a gap of at least 8 mm is left between the floor and the canvas. But such a gap will adversely affect sound insulation, so it is better to build a ventilation valve with a sound absorber into the door (approximate price - from 1,200 rubles).

Material prepared: Vladimir Grigoriev

Tsugunov Anton Valerievich

Reading time: 10 minutes

The operating conditions of doors directly depend on the environment. In the bathroom, for example, even if there is a powerful ventilation system, the humidity level will be higher than the average for the house, or even will “walk”, then rising to maximum values, then falling below the norm. It is from this stereotype that people are repelled when choosing doors to the bathroom. In part, this is correct - after a couple of months, who wants to face the problem of an unlocked door or see treacherous traces of rust on gilded hinges.

On the other hand, manufacturers have long foreseen these moments and protected the products so that they function without failures in the most aggressive environment. True, this applies only to quality products. This means that buyers have the opportunity to install door structures with the same design throughout the apartment - deaf or with glass, hinged or sliding, leading to all adjacent rooms, including a bathroom, a bathroom, a dressing room, etc.
The isolated status of the doors to the bathroom still has a place to be, but it does not concern design and price, but other factors. When choosing, pay attention to the following characteristics:

Dimensions: depend on the opening, which can be standard or non-standard;
door covering;
Comfortable constipation;
Type of opening, and how suitable it is for your room.

These questions, as well as how to choose a bathroom door according to the material, will be covered in detail in the following paragraphs. This article was written by specialists from the V Dom online store, who will help you choose interior doors for any room.

How to order bathroom doors of the right size and not overpay?

How not to overpay for interior doors to the bathroom, toilet is one of the key issues, because it is these structures, or rather the openings for them, that do not always fit into the standard dimensions.

So, let's go in order - there are 2 options for the development of events:

Doorways conform to common standard sizes;
The opening is too narrow and low.

Which opening is considered standard

It would be correct to consider the standardization of the dimensions of interior doors from two sides.

Firstly, the parameters given in the regulatory documents - GOSTs are taken into account.

Secondly, this is a line of standard sizes installed at a particular manufacturer. When choosing doors, we are interested in this moment, because. if some size is considered non-standard at the factory, then when ordering doors of this size, the overpayment will be from 30 to 50%.

What do GOSTs say?

In the regulatory documentation, standards for interior doors are conventionally divided into 2 categories:

For a height of 1900 mm - doors can be 550, 600 mm wide;
For a height of 2000 mm - 600-900 mm (in increments of 100 mm).

But at enterprises producing interior doors, the height is 1900 mm. in half of the cases it is considered non-standard, and requires an additional payment.

Attention! If overpaying is not included in your plans - look for your favorite models from those manufacturers who make doors 1900 mm high. without additional payments.

Most modern apartments are equipped with openings according to the second standard size, leaving a height of 2 m.

The width of the doors is usually selected in accordance with the purpose of the room:

In rooms - 80 mm;
To the kitchen - 70 mm;
In the bathroom, bathroom - 60 mm.

That is, for bathrooms and toilets in some types of typical houses, a minimum opening is left. This option is no longer considered inconvenient for buyers today. For most manufacturers, each series of interior doors is available in the entire existing line of sizes that fit within the standards. This means that you can order 3-4 or more doors of the same design in one place at once to be installed in the hallway at the exits to the bathroom, bathroom, living room, kitchen and other rooms (in accordance with the layout).

Conclusion: you are lucky if all doorways, including those for utility rooms, have the same height and approximately the same width. Before you is a huge assortment of models from all existing materials, at a price of 2 to 50 or more thousand rubles, of any color and style.

If the opening does not fit into the established standards - what to do?

Doors to the bathroom in 137 series houses often do not fit into any standards at all. In special cases, the issue is such that it is no longer a matter of price. We need to find a factory that can even make doors of this size.

Factories that manufacture too high (low) or wide (narrow) canvases can be found on the Internet if you type “interior doors to order in non-standard openings” into the search box, and the city in which you live. Of course, such products are not put into circulation, they are not among the finished designs, so get ready for the fact that:

Doors will be made to order, from 2 weeks to 2 months;
The price for 1 position will increase by 30-50%;
The installation cost will also increase.

The production of standard doors in factories has been put on stream. Accordingly, the equipment is configured for a certain standard size. To obtain a design with larger or smaller parameters, it will be necessary to change the settings of the machines, and possibly the technology, which will lead to even greater labor costs and an increase in cost.

What to do if doors of non-standard sizes are required for the bathroom and toilet, and there is no way to overpay?

Search for manufacturers that produce models of the required sizes, and then select factories among the selected names where the price for non-standard sizes will be with a minimum overpayment.
At the repair stage, you can expand the opening, if the project allows. This is the best option, because it will solve the problem of choosing doors once and for all, will allow you to bring in overall furniture and plumbing without any problems, and will provide a lot of options for choosing a design.
Cut the door leaf to height. The method is not suitable for film-coated models, and for solid wood doors it is considered a reasonable solution if a professional does the work.

What materials can doors be installed in the bathroom, and which ones should not be used?

Why did we decide to highlight the problem of choosing bathroom doors? Of course, it's not just a few drops of water that can accidentally fall on the canvas: the drip option just doesn't do as much harm as the cyclically changing atmosphere. Even with powerful supply and exhaust ventilation, it is almost impossible to maintain the humidity and temperature in the bathroom at the same level.

What doors are installed in the bathroom?

In general, interior doors differ from each other in three key features:

base material;
coated;
By design.

The moisture resistance of the canvas depends on each of them. That is, some models are categorically not recommended for installation in places with a changing atmosphere, while others, on the contrary, are able to withstand direct water ingress for a long time and the constant presence of condensate.

Of the three factors listed, it is the base material that has the least effect on moisture resistance. Great importance is given to the choice of coating - it creates protection and prevents the penetration of moisture into the inner layers. A lot also depends on the quality of assembly and the type of construction, because if a microgap remains at the junctions of the panels and the base or at the edges, it will thus become a “moisture bridge” and over time, from a small defect, it will turn into a huge gap in the form of a swollen non-closing canvas.

However, the door to the bathroom is not always PVC or eco-veneer. Modern materials and processing technologies make it possible to use solid wood structures for this purpose. Which models are able to constantly withstand the onslaught of high humidity - let's discuss in detail:

Inexpensive film doors

Laminated with an inexpensive smooth cellulose film with a wood pattern;
Covered with a thin eco-veneer 0.1-0.3 mm thick based on paper, imitating the texture and pattern of the array.

Their main advantage is low price. Nevertheless, if there is some cash reserve, we do not recommend installing such models in the bathroom, especially in a small one, where humidity manifests itself in two ways - in the form of steam and with direct droplets. Even very high-quality protection weakens over time, the paper gets wet, moisture penetrates to MDF, which, although it is considered moisture resistant, will begin to swell after a year or two. The door will change in size and you will have difficulty closing. Yes, and the appearance of the model will suffer. Therefore, if it is a laminate, then it is worth refusing, or it will not last long.

Film doors of the middle price segment

High-quality, durable PVC films;
Polypropylene coatings, including high-class eco-veneer with a thickness of 0.4-0.5 mm.

Films protect the internal contents by 100% in the event that effective technologies were used during their application and there is not the slightest defect on the surface. The strength of synthetic materials is sufficient to repel impacts and small scratches. And this is important, because in the case of interior doors made of PVC and eco-veneer, you should pay attention to the level of their performance. Water can hit them if there is a loophole for it.

Film doors are divided into 2 groups by design:

Panel boards - from a single piece of fabric, possibly with a decor applied by milling;
Prefabricated - paneled and tsargovye, consisting of a base (frame) and inserts from MDF, glass.

Paneled bathroom doors with quality assembly are the right choice.

These are canvases made from a single sheet of MDF or milled. The second ones look like paneled ones (when the inserts go separately from the frame), yet this is their imitation, which is performed for the purpose of decoration.

Coating of panel doors with films is carried out in stages. First, the material as a whole sheet (PVC films and eco-veneer are sold in the form of rolls) is applied to the facades. After that, narrow sidewalls (edges) are glued. As a result, a seam is formed at the junction. This is the first weak point of panel structures. The susceptibility of the door to moisture will depend on how well the connection is made, how tightly the overlap is made.

Milled doors are covered with a film using the same technology.

There is a third version of panel models - with glass inserts. In the places where they are installed, an MDF plate is cut out, and a beam is laid inside for attaching glass. The joint where the wood board meets the glass is the second weak point of the structure.

When choosing a panel film door to the bathroom, carefully inspect the edges and the junction of the glass. You can take them only if there are no defects on the surface - even the smallest ones.

Paneled and tsargovy PVC doors, eco-veneer in the bathroom - 100% your option!

In this case, too, all attention is on the quality of the product. In fact, such a door is a prefabricated constructor. The advantage lies in the technology of coating with protective materials: not the entire finished door is wrapped with rolled films, but each element separately. At the same time, the joints at the panels are left on the side that will be hidden inside the groove of the frame.

The second point is the edges: for paneled structures, the frames are completely wrapped, without creating joints on the sidewalls, so they are completely devoid of those weak points that panel sheets have. But for both, the upper and lower ends remain open - as a rule, they are not covered with films, because they are not visible.

Veneered doors

This refers to doors covered with natural veneer. The same wood that is known to be very hygroscopic (especially some varieties). Moisture resistance depends on the quality and type of protection. For veneered doors, this role is played by varnish - they carefully cover all surfaces, except for the upper and lower ends. If glass panels are used, then they are mounted together with seals, achieving a tight and reliable connection.

Enamel doors

In the rating of materials for protecting canvases from water and moisture, this is the undisputed leader. Enamel lays evenly on all parts of the structure. The glass installation method is similar to that described above. Weak points are the ends at the top and bottom.

Is it possible to install solid wood doors in the bathroom

Segment of the most durable, reliable and expensive interior doors. Given the tendency of wood to absorb moisture, is it worth it to spend a lot of money on a product that may not be suitable for use in the bathroom. Or did the producers cope with this task?

Different types of wood are used in the production of doors. The most common are 5 types (in decreasing order of cost):

Ash;
Alder;
Pine.

How the finished product will react to increased humidity depends on the type of wood and on the protection option. We will deal with the varieties of the array and the level of their hygroscopicity a little later. First, about protective coatings - they are of two types:

Breathable - paint, wax, impregnation;
Non-breathable - primers, enamels, varnishes.

The first to produce a deeper processing of the array. Substances - stronger or weaker - penetrate into the inner layers, leaving open pores, thanks to which the tree "breathes" and ensures normal air exchange in the room. Materials from the second category clog pores, thereby providing a more reliable natural protection of wood from moisture.

Now - about the moisture resistance of wood species.

Pine

Its advantages are low price, beautiful pattern, high thermal insulation, a huge amount of resins in wood, which make it relatively resistant to moisture. It is for this reason that doors made of untreated pine are often found. But living material with open pores will react to moisture. Given the friability of wood, it will expand or contract strongly. To close the pores and give additional water-repellent properties, it is impregnated with wax. Often it is tinted and varnished. It is not recommended to paint with enamel, because. due to the high expansion coefficient, it may crack.

Alder

Alder is slightly denser than pine, but without resins. Therefore, it absorbs moisture much more strongly. As coatings, it is necessary to choose denser compositions: primer, enamel, varnish. The breed is often used for surface finishing in saunas. Wood does not overheat, thereby preventing burns. People are also attracted by its beautiful reddish hue and pleasant smell, similar to the aroma of cognac.

Oak

Suitable breed for the manufacture of doors to the bathroom. It behaves well in conditions of high humidity, provided that the wood is well dried and securely coated with the right compositions. Oak absorbs moisture well, but does not change much in size due to the density of the wood. It is not necessary to cover it with dense opaque coatings. Great for paint or varnish.

Ash

Ash is similar to oak, but if the latter becomes as strong as metal under water (remember bog oak), then ash begins to rot. Therefore, ash trees are not placed outdoors. In damp areas, antiseptic treatment is required, but this is normal for natural wood. In general, when used in apartments and houses, it is no different from oak and the outer coatings are generally identical.

Beech

As strong as oak, but unlike the latter, it is very hygroscopic, much like alder. If we talk about pure untreated wood, then it is not recommended to use it even under normal conditions, not to mention high humidity. Solid beech doors should be finished with as dense coatings as possible. In the bathroom it is better to install doors in enamel.

Fittings for bathroom doors - hinges, handles, wraps

Bathroom, bathroom - the most visited places in an apartment or house. Doors to these rooms are under increased stress, especially in large families or communal apartments. It turns out that when choosing fittings, attention should be paid not only to its moisture resistance and corrosion protection, but also to the reliability of the opening and locking mechanisms.

Locks

Plumbing wrap;
Handle-knob with built-in wrapping;
Latch or latch.

Plumbing wrapping is considered the most convenient. It is a standard mortise lock. Unlike the mechanisms installed in the entrance doors, it has a simple design and one tongue that flies into the groove and is locked with a latch. The advantage of this design is reliability, although installation requires more effort than installing a simple latch, and the service is relatively expensive.

Plumbing locks are so called because they do not have special secrecy, but perform a single mission - they prevent accidental opening of the room when it is occupied. In some mechanisms, a small hole is provided. It is necessary for an adult to be able to open the door with a hairpin if a child who has played too much suddenly locks the door.

The knob is a mechanism with a ball-shaped handle, in the center of which there is a small rotating latch. It is worth installing it perpendicularly, and the mechanism is blocked, it becomes impossible to open it from the outside. Installation is carried out in 2 holes - one through is drilled in the canvas, the second is right there, but from the end.

Latch or latch - why not? Such devices are inexpensive, for installation it is not necessary to drill holes. The downside is that if the child is locked inside, the door will have to be broken.

loops

They have a triple load - from high humidity, frequent opening and the weight of the structure.

So that the hinges do not corrode, choose stainless steel or brass components, but nickel-plated or chrome-plated.

Of all the types of hinge designs, one should not stop at the butterfly models. Suitable here:

Card;
Mortise;
Hidden.

Card loops are the cheapest. If you focus on strength, take brass ones - they are stronger and able to withstand a lot of weight. They look like 2 metal plates connected to each other by a pin inside the cylinder. Installation is made on self-tapping screws.

Mortise models are similar to card models, but for their installation at the ends, at the attachment points, a recess is cut out the size of a loop bar. The fittings are inserted into the resulting niche and fastened to the screws.

Hidden hinges are the most expensive and difficult to install. They create a more aesthetic appearance, because they remain invisible in any position of the canvas.

Do you need a threshold?

Threshold on the door to the bathroom is not necessary. A small gap below performs the function of natural ventilation. Some argue that the threshold in the bathroom is necessary so that in the event of a flood, it holds water for some time and does not allow it to pour into the living area. Experts say that for these purposes, the bathroom provides a low laying of the floor. Indeed, the level of flooring in the bathroom is lower than in the rooms, which means that the threshold, as a restraining element, is not needed.

Which of the existing options for closing doors optimally solve all 4 designated tasks. Recall that there are 5 varieties in total:

Swing.
Sliding - on a roller mechanism installed along the wall.
Sliding - in a pencil case.
Folding (books).
Rotodveri.

Swing doors to the bathroom - the best solution

The classic version of the door, which is used in large-scale and individual construction. The swing door is more suitable for use in the bathroom than other designs. The main thing is to choose the right material, fittings and opening side (left, right), assessing the situation around in advance. For example, if the bathroom and the bathroom are nearby, and the entrance to the kitchen is located on an adjacent wall (a traditional version of many standard projects), you should consider the location method so that the open doors do not interfere with each other.

Benefits of swing doors:

Relatively low price due to a simple and understandable hanging mechanism;
Simple, fast installation;
High degree of tightness (if installed correctly): achieved through high-quality seals;
Soundproofing: outside you can not hear the sound of a water jet knocking on the bottom of a steel bath;
Reliability and maintainability of fittings, which are also easy to replace.

Sliding systems - pros and cons

General advantages of all types of sliding doors:

Easy opening of the sash - no effort is required even for a child;
Space saving;
External attractiveness, stylish design;
There is no threshold;
The ability to install automation systems to fix the web in a certain position;
The kit includes stoppers, limiters that prevent automatic closing.

Flaws:

The high cost of fittings, locks;
Minimum soundproofing;
Difficult installation, especially "pencil case" systems;
Special requirements for adjacent walls - they must be free so that nothing prevents the canvas from moving.

Both types of sliding structures are installed in the bathroom - ordinary (along the wall) and “in a pencil case”.

Sliding along the wall

The simplest system of existing sliding options. Top and bottom guides are mounted. The overlay cloth on rollers moves to the left/to the right. The design is not suitable for installation in very cramped hallways, where the entrance to the bathroom and the bathroom are located on the same wall at a distance of several centimeters and are separated from each other by a thin partition.

The second point - nothing can be put or hung on the wall: a table, a picture, a vase - everything will prevent opening.

The third disadvantage is that it is impossible to achieve tight closure. The lack of tightness in our case is not an unimportant factor. Water vapor in the form of condensate will accumulate on the walls and ceiling of the adjacent room. This can render the finish unusable if wallpaper is used in the design.

Yet compared to alternative sliding models, this one is the cheapest and easiest. Sometimes you don’t even need to buy a new canvas - you can simply remove the old one from the hinges and install it on the rails: the fittings are available and inexpensive.

Sliding in a pencil case

Not suitable for all rooms, because it requires even more space around the opening for installation. As a rule, it is necessary to leave at least 1 m on the left and right sides, and also provide for a distance from above where the cornice will be installed.

Installation options:

Break the wall, expand the opening by about 2 times;
Install the "pencil case" in the opening, where there was previously a double-leaf swing door;
Build a false wall to make a "pencil case" out of a swing door.

Please note that the mechanism that ensures the movement of the web will be built into the wall and operated in high humidity conditions. Pay attention to its quality, because if the hardware breaks, you will have to break the wall to repair or replace it.

Folding doors

2 models available:

Book;
Harmonic.

Advantages:

Saving usable space;
Not demanding on adjacent walls, because they do not move to the side;
They allow the door to be opened to the desired distance - it is not necessary to open the entire canvas if it is not necessary.

The structures are equipped with seals to achieve hermetic closure. Disadvantages - complex installation and expensive mechanism.

Rotodveri

The rotor system is a synthesis of a hinged and sliding structure. Opening inward and outward is allowed, as in pendulum options. When the canvas is opened, it rotates around an axis installed in the center, and also shifts to the side. That is, being open, the door remains in the opening, but one half is in the bathroom, the other is in the hallway or bedroom.

Disadvantages - minimal tightness and humidity, constantly affecting the expensive mechanism. If we consider such systems for the bathroom, then with great care, in the presence of good ventilation and a large area where the sink and shower are at a decent distance from the entrance.

Conclusion! Which door to choose in the bathroom - today practically does not depend on the material. Manufacturers have long removed this issue from the agenda and provided customers with an unlimited range of designs, colors and prices. Only one thing depends on us - to control how well the assembly and decorative coating are done, as well as what accessories are attached to the product and whether it meets your ideas of beauty and comfort. The main point that hinders the free choice of doors is the issue of non-standard sizes. If you have any questions or need help in choosing, please contact us, the specialists of the door store "V Dom" will answer all your questions.