Thinking about how to improve the look of their car without spending a lot of money and making the car stand out, many motorists decide to paint the rims. Indeed, from such a procedure a noticeable effect is obtained, which depends, first of all, on the chosen color. Also, the advantage of painting is the absence of the need for official registration, as is the case with body painting.
Painting of steel rims suitable for any car, it can decorate an expensive foreign car, and an old domestic car. A wide range of colors will emphasize the individuality of each car and its owner.
Service painting of stamped wheels
Specialists for this procedure use modern powder paints, which create a fairly even and durable coating. Powder-coated discs become more resistant to sub-zero and plus temperatures, their paint does not fall off, and you can completely forget about burnout. Powder coating will protect the wheels from the effects of corrosion, scratches will be a thing of the past.
First, defects are removed by sandblasting, phosphating will protect the wheels from rust, and several layers of powder paint will make the wheels more durable.
In the service center, it is distinguished by process reliability and high-quality results. Each customer will be able to find the color that best suits the car.
Benefits of hiring specialists
At first glance, painting stamped rims seems like a fairly simple process, and many even believe that doing it yourself can save money. But it's not. After painting with your own hands, after a year or two, the procedure will need to be repeated, and this is an additional cost of personal funds. Painting by the hands of professionals will pass without defects, the wheels will emphasize the design of the car. The result will hold securely for many years, so painting stamped wheels, price, which you will need to pay only once, is a better offer for car owners.
Good painting requires not only new equipment, but also reliable specialists who can reliably protect the disc from the bad influence of natural conditions. This paint will last you for many years.
Prices for painting stamped wheels
| Disc diameter | Light alloy cast and forged wheels, not galvanized. Price per set (4 discs) | Light-alloy cast and forged wheels with galvanized coating (chrome, etc.). Price per set (4 discs) | Steel discs. Price per set (4 discs) |
|---|---|---|---|
| up to 11 | 2820,00 | 3660,00 | 2160,00 |
| 11 | 3240,00 | 4180,00 | 2490,00 |
| 12 | 3700,00 | 4700,00 | 2860,00 |
| 13 | 4160,00 | 5220,00 | 3230,00 |
| 14 | 4750,00 | 5900,00 | 3700,00 |
| 15 | 5340,00 | 6600,00 | 4170,00 |
| 16 | 5760,00 | 6980,00 | 4510,00 |
| 17 | 6180,00 | 7550,00 | 4840,00 |
| 18 | 7100,00 | 8520,00 | 5180,00 |
| 19 | 7020,00 | 8490,00 | 5520,00 |
| 20 | 7440,00 | 8960,00 | 5850,00 |
| 21 | 7860,00 | 9430,00 | 6190,00 |
| 22 | 8490,00 | 10120,00 | 6690,00 |
| 23 | 9120,00 | 10800,00 | 7200,00 |
| 24 | 9750,00 | 11480,00 | 7700,00 |
| 25 | 10380,00 | 12160,00 | 8200,00 |
| 26 | 11120,00 | 12845,00 | 8800,00 |
| Over 27 | negotiable | negotiable | negotiable |
What paint to paint stamped wheels? I want to bring them into a divine form.
- Clean, degrease, prime and paint, color depending on the color of the car, gray or silver can be used as a universal option)
- read out from corrosion, treat with a rust converter (orthophosphoric acid if I'm not mistaken), prime it, and paint it with paint for disks, it is sold in car dealerships. classic silver
- It's great about powder coating, but you will need to remove all the paint from the disks ... And at the very least, you take a brush and draw on the outside with any color and any paint. . Paint berm brand sho is or sho horrible... . You can also paint in different colors... For example, I saw on a beige shoe the inside is red, and the outside is white .... Inspiring… I painted with sadolin.. There was a residue from painting the car.. . But the paint looks nice but soft. . At the tire fitting, the edges have already pokotsa ...
- Preparatory work
Renewing discs is best done between seasons, in autumn or spring. It is necessary to begin preparation with a thorough cleaning of dirt, old paint and rust. Cleaning discs is best done with a metal brush nozzle for a drill or grinder.
Further, it is best to use medium and fine sandpaper to finish the surface of the discs. It is better to spend more time preparing than to suffer with the wheels, constantly pumping up during further operation.Work must be done in a protective mask or goggles and preferably in a respirator. After stripping, wash the discs with water and treat with a rust converter. Please note that the transducer starts its corrosive work 30 minutes after use and at an acceptable temperature. environment. Degrease the surface of the discs with white alcohol a couple of hours after using the rust converter and allow the surface to dry. I want to give a little advice. Before you start painting the discs, it is necessary to moisten the floor with water so as not to raise dust. Install discs on 5 liter canisters filled with water.
Primer
Before priming, shake the can with soil for 15 seconds and it is best to warm it up on a battery or in the sun before use.
You need to prime the disc several times, taking 5 minute breaks between layers. Then let the primer dry for 24 hours. After, we clean the hooks and irregularities on the surface of the discs with fine sandpaper and water. The disc surface must be perfect.Painting
We paint over the discs in 2-3 layers with breaks of 5 minutes. So the wheels are painted. After an hour of rest, take an auto varnish and apply it on the painted surface of the discs from a distance of 35-40 cm in the same way, with breaks between layers. Two, three coats of auto varnish will be enough to protect the paint, but there is a small nuance, auto varnish gains maximum strength after 8-9 days after application.Outcome
Let's summarize: the costs required for repairing disks at specialized stations can be $150-200, and do-it-yourself repair of stamped disks can cost $35-40. Saving is also a kind of earnings! - Spray? Degrease, primer, paint.
- Good day. My husband also tried to paint his wheels himself. but after that they had enough sight for a couple of weeks. then he went to this service http://mtlink.ru/. so he got some kind of coverage there. wheels are like new now
- A spray can is useless, it won't last long. Need powder coating
Stamped discs are considered the most durable, since all that can deteriorate over time is the paintwork. The steel from which such models are made is able to withstand all the tests of current roads. But the paint on the autodisk is gradually scratched and corrosion appears over time. In order to avoid serious damage, it is changed to a new one, or simply re-painted.
The wheel does not need to be stripped before painting. In tires, the pressure is reduced as much as possible and simply sealed along the border with masking tape. This prevents paint from getting on them. But if the auto disk has been severely damaged by corrosion, then it will still have to be disassembled to clean the rust on the rim.
Painting of stampings
Special car services perform painting quickly and efficiently, but they charge a lot of money for it. In such a workshop, discs are cleaned of old coating and rust using sandblasting, which is carried out on special equipment. Such a car is expensive, so not every motorist can find it in the garage.
Auto disks are also painted with the help of an airbrush and high-quality paint. That is why this procedure costs a lot. But those motorists who want to put the wheels in order at no extra cost can repaint them themselves. And for this you don’t need to buy expensive equipment, but all because almost all the materials that are needed will surely be found by every driver in the garage.
Painting stampings in a car workshop Do-it-yourself painting of stamped discs
The very first step in self-painting discs is their proper preparation. The whole result of the work done depends on this. The materials you will need are very easy to get, and they are inexpensive. In order to paint the rim, you will need:
- sandpaper of different grain sizes;
- drill with a hard wire nozzle;
- degreaser;
- masking tape;
- primer;
- automotive putty;
- quality paint;
To begin with, the autodisk should be washed from dirt and dried.
Then you can start processing and removing the old layer of paint. But such work can take more than one day, so if the work surface is not very succumbed to corrosion, then all the paint can not be removed. It is enough to walk with a drill with a nozzle and remove small rust.
But if there is a desire to do the job with high quality, then you will need to sweat properly with the removal of all the old paint. If the rim has obvious defects that have not been eliminated during pre-treatment, then the surface must be corrected with machine putty. But before that, degrease the autodisk with alcohol, gasoline or a special tool. With the help of putty, all dents and deep scratches are leveled.
Note!
Putty must be applied in several layers, and each layer must be made thin, otherwise it will not dry well.
After the putty has completely dried, the turn of applying the primer comes. Apply the product at a distance of at least 25 cm, and also make several layers. Each of them needs to dry for about 20 minutes. It is necessary to carefully monitor the spray and not linger in one place for a long time, otherwise streaks form. Next, the soil will need to dry for about three hours, but ideally a day is better so that it grabs well.
Processing with a drill with a nozzle After all the preliminary stages, the moment of painting comes. And here, for beginners, the question often arises: how to paint the car wheels yourself (stamping)? There are really few options. Coloring can be carried out with special acrylic paint, powder, liquid rubber. Powder immediately disappears, since this method can only be painted in a car repair shop for special. equipment.
Liquid rubber will work, but you need to be able to work with it, and it costs more than an aerosol can. The best option for such a case can be considered paint in a spray can.
It is inexpensive and very easy to use. Here are some helpful tips to help you paint thoroughly:
- the can must be constantly shaken during operation;
- the paint application distance must be at least 20 cm;
- the air temperature in the room or on the street should not be very low;
- apply the paint in several layers, each of which must dry for at least 30 minutes;
- do not keep the can for a long time in one place, in order to avoid the formation of streaks;
If the streaks still turned out, then the problem can be corrected with fine-grained sandpaper. But this can only be done on the first layers of paint. After drying, varnish is applied. The wheels should dry out for 5-6 days, and during this period it is undesirable to touch them at all. If you do not allow the paint to completely dry, then there is a risk of scratching the discs during assembly. Painting stampings with your own hands is quite possible, the main thing is to adhere to all stages of preparation.
Paint, varnish and primer must be of high quality, and preferably from the same manufacturer.
Required Materials Auto disk tuning
Tuning is one of the ways that allows you to distinguish a car from all other vehicles. And there are many types of such tuning, for example:
- installation of new plugs;
- unusual painting of auto disks;
- chrome plating;
- inlay;
- backlight;
- unwelding.
Installing plugs is a replacement of old ones with new, more original ones. You can simply buy a new kit and paint it in the desired color, or make your own. The main thing in this matter is skillful hands and imagination.
The most common way to improve can be considered an unusual painting. This means that you will not just have to repaint the disc in metallic, but choose bright, catchy colors, and maybe even several.
Chrome plating is also quite popular with car enthusiasts, as it gives the wheels an incredibly stylish look. In this case, a metallic coating with a mirror effect is created. The inlay is a decoration of the rim with Swarovski crystals. This procedure is laborious and quite expensive. But the wheels in the end look just amazing.
The backlight looks very effective at night.
For this method, neon tubes or neon tape are used. Installing them on a disk is not difficult even for a beginner.
And the last method of improvement is unwelding. It involves expanding the disk by sawing parts and adding more metal to the structure. But this method has more disadvantages than advantages.
What paint to paint auto stamping wheels in two colors
It is better to use paint in a spray can or an airbrush for such purposes. Staining usually occurs in two shades, while this process does not require special skills. The rim of a stamped disc is painted in one tone, and the middle in another. All manipulations are performed using masking tape and oilcloth.
Painting with multiple colors The place necessary for painting is left uncovered, and everything else must be covered with foil and secured with masking tape. After the paint has dried, you should close the painted area and paint where there is no paint yet. Even in the case of double paint, you can use special stencils with a pattern. The main thing is to carefully cover the places where the paint should not fall.
About how to paint the steel wheels of a car yourself and how, is fully described in the article. An important point in this matter is its quality preparation. You should also pay special attention to your own safety. Gloves, mask and respirator must be present while working with paints and varnishes.
4 years ago
Welcome!
Painting - it gives not only a beautiful look to some particular part, but also saves the part (If it is metal) from corrosion, in addition, depending on what color the part will be painted, its heating in hot weather depends very much, let's take black color, for example, if you have already driven a car covered in black more than once in the heat, then you can imagine how hot it is inside, especially when the car sits in the sun for a long time, the same white color, on the contrary, does not attract the sun's rays and get into such a car in the heat, more or less pleasant.
Note!
To paint stamped discs, you will only need to buy: Two cans of primer, but you will only need to take exactly the color in which the wheels will be painted (If there is no such color, then at least close to it), as well as a can of paint will be needed, white spirit, a couple of rags, one of which should be clean and the second should be more or less and necessarily a room and, of course, warm weather outside, we categorically do not recommend doing this in moisture (The exception is when the garage is heated and you leave the disks in it to lie, before they dry out), so that the work goes faster and with pleasure, take assistants with you, divide the disks among themselves and finish the work much faster and by the way, don’t forget about the skins too, they will also come in handy!
Summary:
How to paint stamped wheels with your own hands?
Note!
If you are planning to paint anything (In our case, these are disks), consider the fact that the surface on which the paint will be applied must be fenced off from dust and similar substances, so it is better to carry out all operations in the garage, even if it is summer outside, there is no you need to apply paint, you can remove it, but you need to apply it to the room, where there is no dust, no dirt, no wind, nothing like that, and then the paint will lie well and will not start flying off over time!
1. To begin with, you will need to remove the wheels if they are on the car (We described how to remove the wheels Already in three articles, you can find all these articles using the search on our website), if you do not have the opportunity to separate the tires from the disks, then in this case, wrap all the rubber with adhesive tape (But this operation will need to be performed only after cleaning the discs from paint, point 2) so that it does not get dirty when painting, or make such a device (see photo below) from two cardboard boxes and then you won’t have to spend too much time on adhesive tape.
2. We turn to cleaning, it is very, very difficult to completely remove all the paint, especially if you work with ordinary skins, so if this happened, then in order not to lose a lot of time, make sure that the paint peels off a little and becomes smooth (see photo below) this will be enough, we will explain in detail how to work with the skin:
Firstly, you will need to buy it, there are many different types of skins (And its real name is “Sandpaper”), but they differ in grain size (The smaller the number of the skin, the coarser the grain will be and vice versa), to remove the paint, take a rougher skin, consult with the sellers, they will give you advice on which one is better to choose, but after cleaning the metal with a rough skin, it will become unpleasant to the touch and the paint will not fall on it as well as it should be, so in order not to was, take an even less rough skin, with which you will complete the work, making the metal near the disk smooth.
And in a nutshell, let's say how to erase the paint with a sandpaper, in general, you will need water (It is best to pour it a little bit into a bucket and, as it gets dirty, pour and pour new water into the bucket) and of course the skins themselves, remember the most important thing, they are constantly wet should be and notice, wet and not wet, that is, you will still need to dip the skin in water, but as soon as you take it out, immediately shake it well so that the main part of the water flies off the skin, and this is necessary in order for the skin to work more successfully, since it moves much better in moisture than on a dry surface and does not scratch so much, and in fact, get to work, namely, rub the disc until it becomes like it was shown approximately in the photo above.
3. There is another way, we are talking about cleaning the paint, for its implementation you will need a specialist. paint remover, it will most likely be in the same store where you will buy paint, this liquid is sold in two types, the first type is in cans, the second type is in a jar, it is best to take the second type, because it corrodes better all the paint (Much better), it is applied with a brush, but it is better to take it in spray cans when there is work to be done with able-bodied places, to which it is really much difficult to crawl with a hand and a brush.
Note!
In the photo above you see how the same special is applied. liquid on the disk and after a while, the paint corrodes (see small photo), of course, not all of it will peel off, but then it will be easier to remove the paint after such processing, and if you also have a drill in the garage with special . with a metal nozzle (see photo below), then turn it on and walk over the entire disc and in less than 5 minutes you will completely remove the paint from the disc!
4. When the paint is removed, you will need to use a clean rag and white spirit, degrease the entire disc with it, dirt and dust should not remain on it, then wipe the white spirit with a more or less clean rag, wait a while until it dries (5-10 minutes) and start applying the primer, do everything at a distance and do not hold the primer can in one place for too long (Drive it), so that there are no jambs at the beginning, practice on the cardboard, just try to paint it and without streaks, it won’t work, try again, understand the most important principle and what distance should be, if the next cardboard box turned out to be painted normally, start painting the discs, do not forget to observe the interval between tinting (Applied the first word, wait 10-15 minutes until it dries and apply next immediately), after several layers of primer have been applied and wait until it dries, apply the paint itself, it is applied in the same way as the primer, with an interval m and with layers, having applied several layers, wait until everything dries (How long the paint will dry is indicated on the can) and you can install the wheels back on the car and drive.
Note!
At the very end, when the paint dries a little bit (although an hour will pass from the last application), the disc can be varnished in addition (It is also sold in spray cans), so it will shine and an additional protective layer will be created, due to which the disc will not start so quickly rot as it will be without varnish!
Additional video clip:
You can see in more detail and clearly how to paint the wheels in the video, which is located just below:
The standard colors of the cheapest stamped wheels do not always satisfy modern car buyers. Therefore, the possibilities of painting these parts are increasingly being used. You can do the procedure yourself, but painting this element is not as easy as you might think. This will require a special type of paint material, as well as the preparation of the stamping itself for the procedure. In order for the painting of stamped disks to be successful with your own hands, you will have to carry out all the processes with high quality.
Any paint job on your car can be overwhelming if you don't have any experience. In addition, it will not be easy to do all the work with disks from a simple cheap aerosol can. It is highly desirable to have access to good materials and normal equipment. Otherwise, it will not be easy to achieve your goals and perform painting work really well. So, let's look at some of the features of high-quality and durable wheel painting.
Whatever materials you decide to paint the wheel with, the preparation must be of high quality. All procedures can be done by hand. Even if you plan to turn to professionals, it is quite possible to do all the work qualitatively on your own and save significant money on this. Before painting the rims, you will have to clean them and remove the old paint, as well as various preparatory procedures. The list of works is as follows:
- old paint is removed with the help of various acids and special compounds, otherwise it cannot be overcome;
- before starting any work with a stamped disk, it is necessary to clean the wheel from dirt;
- then apply a paint remover with a brush to clean the surface to metal or primer;
- then carefully inspect the front surface for chips and deep scratches, deformations;
- if there are irregularities, you can level them with high-quality putty even before painting;
- after all procedures, it is necessary to take a solvent, a soft cloth and degrease the surface of the wheel with high quality.
If the disc is not prepared, it will be impossible to paint it with your own hands or even at the service. Otherwise, all new paint will start to fly off at the first stone encountered on the road. This will not be the most pleasant solution for your car and for its appearance. Of course, the painting of stamped wheels should be thought out in all respects. It is best to give preference to professional materials that will help achieve high quality surfaces.
What materials to choose for painting the wheels of your car?
You can paint stamped discs in two ways. The first is the purchase of high-quality spray cans with an aerosol form of application. This method has the advantage of avoiding complex technologies and materials that can take up more than half of the paint job budget. But the quality of the application may not be the best.
The second method is a simple high-quality spill paint. It is better to choose reinforced acrylic or polymer coatings that will last a long time and not chip from contact with gravel and dust. For painting parts such as stamped wheels, only the most expensive and wealthy materials are chosen. You will need no more than 200-250 grams of paint per wheel to cover both sides.
To do the work with your own hands and paint the car parts with really high quality, you just need to practice a little on other solutions. Keep in mind that good materials are expensive, so you should not allow them to be overused. Spray cans apply paint with low pressure, so they require more thorough coating skills. There are such requirements for painting:
- stamped discs should be immediately placed on the surface where they do not have to be touched and moved;
- the inside is covered first to get a little more skills and capabilities of the painter;
- then it is worth waiting a bit and then coating the outside to get an excellent coverage;
- you can apply from 3 to 6 layers, choosing the amount at your discretion, but it is better not to exceed these figures;
- after application, allow the stamped disc to dry for several hours.
A day after painting it is better not to touch the details. There are many videos and recommendations on how to paint stamped wheels. But only a few give really useful advice to follow. You can take advantage of professional videos to learn how to do everything yourself. With the right approach, you will have no difficulty in painting even such complex surfaces as wheels.
Summing up
Simple stamped rims can be freshened up with a quality paint job or completely restyled. Often, car owners perform tasks with the help of bright colors, highlighting the appearance of these vehicle parts. It may not be so easy to perform all the procedures with your own hands. The reason for this is the complexity of the selection of materials and their direct application. But you can easily get expert advice or watch professional videos describing the procedure.
There is a lot of information in the public domain that will help you do everything right and quickly, paint wheels without involving specialists. If you don't have a compressor, choose expensive spray paint. We immediately recommend taking the material with a margin in order to learn how to apply it normally before painting work. Stamped discs will acquire a completely different appearance and will delight you with their design with the proper quality of all procedures. You don't have to go to a specialist to get good results.
Loading...