How to wash in the bath for disinfection. Safe detergent for the bath. Quarantine zones inside the bath

Glass doors are beautiful and easy to clean, but they also get dirty faster than wood doors. Photo: 95°

Most homeowners have long acquired saunas and intensively exploit these premises. How to preserve the finish in an extremely humid and hot climate of the steam room, avoid the appearance of unpleasant odors and mold, and audit fire-hazardous components and structures?

After each session, it is necessary to raise the wooden ladders, remove the shelf screens and wipe the floor throughout the room.
After each session, it is desirable to wash the shelves with a hard brush (sponge, washcloth on the handle) dipped in boiling water.
After cleaning, you should ventilate the room for at least three hours, and even better, leave the door and ventilation valves open all night. Floor drains should be dried in an upright position, leaning against shelves or walls.

One of the reasons for the aging of the finish is moisture as a result of steam condensation. Therefore, it is necessary to wait until the walls (and not just the air) heat up, and only then start steaming. Photo: Harvia

Approximately every 10 sessions, it is necessary to wash the stones and remove the stone chips from. The stones are first cleaned with a hard sponge and slab cleaner, and then rinsed in clean water.
Once, and preferably twice a year, the walls must be covered with a special varnish for the sauna, and the shelves must be impregnated with oil. Before this, contaminated surfaces are cleaned with a well-ground scraper and sanded with sandpaper (P100 or P120). Deep fungal infections can be moistened with a chlorine disinfectant, but after that, a strong smell of chlorine will remain in the room for several days.

To check the ventilation duct, you just need to remove (completely unscrew) the valve cover, Photo: Ecosauna

It is necessary to periodically check the performance of ventilation valves and channels: dust, dirt and cobwebs can significantly reduce the throughput of the hood.
If the stove is wood-burning, then at least once a year it is necessary to clean the chimney, otherwise there is a risk of soot igniting in the chimney. And of course, we must not forget to remove the ash from the ash box every 2-3 fireboxes, otherwise the firewood simply will not flare up. At the electric heater, according to the instructions, you need to occasionally tighten the terminal clamps - manufacturers recommend inviting a specialist for this.

With regular overheating, the tree gradually changes color and begins to char. At a certain stage, it can ignite spontaneously at a temperature of 200-250 ° C

Wooden parts located close to the chimney should be inspected once or twice a year for changes in color and structure. In this case, it is highly desirable to disassemble the chimney passage module, remove metal screens and other elements that interfere with the revision. The brownish hue, cracking and loose top layer of wood signal the danger of its spontaneous combustion.

An electric stove is safer than a wood stove, but it also requires attention, since the temperature of the heating elements reaches 400 ° C. Photo: IKI

If a drain floor is made in the sauna, it is required to clean the trays and ladders from leaves and other contaminants. To avoid the penetration of odors from the sewerage into the steam room during breaks in the use of the sauna, it is advisable to install a drain with a dry seal.

The stones are washed every 2-4 months, and after 3-4 years of use, it is better to replace them with new ones. Photo: Bankov

In the sauna, colorless coatings are used, since most tinting compounds emit harmful substances when heated. Photo: Tikkurila

If you like wood of saturated colors, you should immediately purchase cedar lining. Photo: Bankov

Bath owners often have disputes about the need for a special product designed exclusively for washing baths, as well as saunas. Most believe that the usual universal methods of home care will do, but some believe that the presence of a specialized tool is mandatory.

On the territory of Russia, baths, as a rule, are of a slightly different nature than in other countries. We have a lot of them, and in the villages this is generally a common phenomenon, since next to each residential house there is an equally beautiful bathhouse. However, in our case, these institutions are intended for individual use, maximum for the family, but in other countries, baths are public institutions. Therefore, the presence is quite in demand among the population.

What surfaces is the product intended for? Yes, for everyone imaginable. With it, you can process wooden walls and floors, tiles, glass elements and much more. Based on this, a wide range of applications can be determined.

It is worth starting with the environment and atmosphere that reigns inside the steam rooms, baths, saunas. Their main purpose is to take a steam bath, wash. Therefore, water and high temperature are constant companions of such premises. The temperature regime varies from 60 to 100 degrees depending on preferences manually: pouring cold water on the stones (to cool the ardor), or throwing firewood into the stove / switching the artificial apparatus to a higher setting (to add heat).

Constant temperature fluctuations, an increased degree of humidity, the use of wood materials characteristic of saunas determined the need for

Overview of wood as the main material for building a bath

Why do people use mainly wood in the construction of steam rooms? Why is she so good? And are there any downsides to this material? Let's find out further. Let's start with positive ratings.

First of all, it is worth emphasizing the 100% environmental friendliness and naturalness of the selected material. Currently, it is also in demand, as it was before. The properties of the tree determined its purpose: in winter, it allows you to keep a maximum of warm air, and in summer, on the contrary, it keeps cool indoors. Yes, and wood greatly facilitates the regulation of various temperatures - and in the bath this is a huge plus.

But any phenomenon must be considered from two sides in order to have a clear and complete picture. The negative trends include such qualities of wooden materials as the most rapid and simple degree of flammability, as well as the accumulation of moisture in their pores, which subsequently leads to swelling and a change in the level of hardness, that is, the loss of their original characteristics. Special care is required for wood components, including the use safe detergent for baths. These premises are also subject to the harmful effects of all kinds of insects, the neighborhood with which a person will not be pleased. There are frequent cases of fungal formations on walls and ceilings in buildings in which an increased level of humidity is set. Thus, once again it is worth emphasizing the implementation of proper care for such an organic material as wood, which allows you to improve the original properties and prevent negative consequences that appear during operation.

A range of specialized sauna care products

It is worth noting that, despite its narrow focus, the market for detergents intended exclusively for the treatment of baths is very rich in various offers.

Let's understand the essence of such a tool. It is a combination of chemical components that have a cleansing effect on dirty surfaces (wood, tiles, glass, and so on), disinfectant properties. It also provides for the impossibility of further accumulation of wet vapors on the tree, that is, there will be no absorption and swelling of the fibers. There are also substances in the composition that act on insects that have settled in the bath - they destroy them.

So what safe bath detergent will be the most efficient? Conventionally, all the wealth of this market segment can be divided into four groups:

Organic - fight well with humidity in the room, fumes accumulating on the tree. After their application, a protective layer of a special film is formed on it, which opposes the process of absorption of wet steam by the wood.
Oil based - no explanation needed here.
Diluted with water - at the exit from the production, they are concentrated substances that must be mixed with an aqueous liquid during use. Designed for all types of materials from which the surfaces are made. Very efficient.
Mixed - products with high disinfectant properties. It is recommended to use them in the process of building baths, saunas. After all, it is this fact that will help to preserve it in the future, reduce the level of flammability of the object and destroy the harmful insects that settle.

It is worth emphasizing that, although these are chemical compounds, they are characterized by safety for humans and the absence of an irritating odor. These factors greatly facilitate the work with drugs.

How and when to use the bath detergent of your choice?

Compliance with the rules that are reflected in the instructions for the purchased product is the key to the highest degree of safety of the work process, as well as the effectiveness of the manipulations performed. It is necessary to follow the surface treatment technology so that the result is really the one you expect at first. Note that sauna cleaning is possible at two stages: during construction (preventive purpose), during the operation of the bath (“treatment” of infected wood). Prevention is always better than cure, because it is ahead of the development of problems.

During the construction period, the steam room is completely processed (all log cabins, boards that are used in construction). This is done for the following purposes: to prevent the destruction of the tree cover by insects, fire, and other phenomena. One of the many bonuses of such an event is the extension of the service life by as much as seven years. Of course, these figures are arbitrary, but proper care will ensure a long operational period.

The already constructed building is subject to periodic maintenance. The product you purchased will help improve the condition . The market is replete with such goods. But you have to choose safe detergent for the bath.

Surface technology

When using specialized care products, the effectiveness of the results is noticeably increased - you can see them literally after the first time. How is it necessary to carry out processing in order to give the bath an ideal look? We offer an algorithm common to all tools (depending on the type, it will differ slightly, but these are already trifles).

Complete cleaning of the surfaces necessary for work from all kinds of debris, if it is impossible to remove dirt from the walls with a rag, use sandpaper (with a fine abrasive).
AT bath safe detergent a sponge, rag or roller is soaked, with which you will work in the future. You need to apply several layers for a more visible result. Pay special attention to saw cuts and damage to the integrity of the tree. These are the places where microorganisms accumulate the most.
The surface is cleaned with only one selected product. Avoid mixing with third party objects. Otherwise, a reaction of chemicals is possible.
If traces of insects are detected, use disinfectant cleaning methods.
Always strictly follow the rules provided by the manufacturer's instructions.

Specialized mixtures do not contain a substance such as chlorine. Therefore, avoid connecting it with them. The destruction of microbes and bugs, dirt from all types of surfaces, rather dense deposits on the walls - this tool can do everything. Thanks to its use, everything in your bath will become clean: windows, doors, ceilings, walls, floors, glass and stone surfaces and more.

As additional advantages, the following can be mentioned: a pleasant aromatized smell that remains after use, it causes irritation and allergies; no traces and muddy stains from a sponge or brush; removal of fungal and other infections, as well as the absence of toxicity.

What to be guided by when choosing?

The market is rich in products for the bath, so there are some points that you should pay attention to when buying. safe bath detergent. This will allow you to choose the most high-quality model and, at the end of the work, have a more visible result. See who is the manufacturer (foreign countries or Russia). In the first case, the quality will be higher, but, accordingly, the price. Often it is winded up only because of a well-known brand. So, maybe it is worth supporting domestic companies? The cost will be much lower. Just before that, you should turn to the Internet to determine how worthy this product will be. Next, you need to decide what kind of mixture you need.

Target:

- disinfection - antiseptics;

- lowering the level of flammability - flame retardant composition;

- protection against insects and decay - bioprotective agents;

- normal cleaning - detergents.

Processing type:

- from the street - outdoor processing;

- from the inside - internal processing.

Material type:

- wood;

- glass;

- a rock;

- tiles, etc.

Proper care and operation in compliance with the simplest rules will significantly increase the life of the sauna, increasing it by ten years or more.

Purchase method

A special-purpose sauna chemical can be purchased in the traditional way - bought in a store. And you can order online. There are many sites, one of the directions of which is the sale safe bath detergent. By choosing the latter method, you will save your time, and possibly even your money. But in the store you can directly get acquainted with the product, evaluate the integrity of the package, you won’t have to wait long for the moment when you can use the purchased product in practice, evaluate the effectiveness and result.(

Keeping such places for water procedures as baths and saunas in perfect cleanliness is not a whim, but a necessity. Simple cleaning is not enough. Periodic disinfection is needed, especially when it comes to common areas. Current processing here is required after each visit. In this case, the surfaces are treated with disinfectants, for example, a solution of chlorine.

From time to time it is necessary to carry out a complete disinfection by professional means. In public places at least once a month, in home baths and saunas 2-4 times a year, depending on the frequency of use.

Why are there such strict hygiene requirements for cleaning rooms for water procedures?

The conditions in baths and saunas are favorable for the development of pathogens for many reasons, among them:

high humidity;
temperature fluctuations;
the presence of a large number of people indoors without proper medical checks.

Bacteria and fungi get on the surface, clog along with water droplets in the cracks in the wood, where they begin to multiply. Sooner or later, this leads to the infection of visitors with dangerous diseases.

Some believe that microorganisms are not able to withstand the high temperature that is created in the room during the procedures. But this is not so, for the destruction of most of them, more than 100–120 degrees Celsius is required, and such conditions are rarely created in a bath and sauna.

Treatment with disinfectants partially solves the problem, but is also not a reliable measure, because the use of drugs makes it possible to disinfect only surfaces. At the same time, hard-to-reach places are not processed, from which microbes will spread at any time due to water spilling or settling from steam droplets.

Benefits of professional disinfection

Organizations providing disinfection services for saunas and baths use special chemicals. Working with them is unsafe, and at the same time, it is necessary to take into account the characteristics of substances that affect the health of visitors. For processing, generators of cold and hot fog are used, thanks to which disinfectants get into hard-to-reach places, for example, cracks in wood and between shelves.

For companies that provide services to the public and provide baths and saunas for general use, calling licensed disinfection services is a necessity dictated by the requirements of SNIP. After each treatment, disinfection services issue relevant documents confirming the fulfillment of sanitary and hygienic standards.

Periodically, the question arises of how to clean the bath. Sooty ceiling, dirty shelves and floors can spoil the pleasure of taking hygiene procedures.

Fundamental rules

How to clean the soot in the bath? There are certain rules for this. For example, wooden surfaces covered with a layer of soot cannot be wetted.

Wood is a hygroscopic material that quickly absorbs moisture. Together with water, everything that has settled on the surface will be absorbed into the structure of wooden elements - soot, soot, bodily secretions, etc. After the dirt has been absorbed into the surface of the wood, it will be almost impossible to clean the shelves in the bath, walls, floor or ceiling.

Therefore, when deciding how to clean soot in a bath from walls or floors, you should categorically refuse to use such substances and materials as:

laundry soap;
water;
sponges;
spray guns.

All of the above products can only be used for the final cleaning of wooden surfaces, when the soot has already been cleaned dry.

All work on cleaning the bath from soot and soot must be carried out using special protective equipment:

blind goggles;
respirator;
thick rubber gloves.

All this will help prevent the penetration of combustion products into the respiratory tract.

Wall and ceiling cleaning

To solve the problem of how to clean the soot in the bath, they begin with a vacuum cleaner. To do this, you need to walk them on wooden surfaces. Next, you need to carefully sweep the soot and soot from the walls and ceiling with a broom.

Prepared surfaces should be cleaned with sponges with special impregnation. They are sold in hardware stores. During the manufacturing process, such sponges are impregnated with special compounds that destroy soot and soot.

Sponges get dirty quickly, so you need to purchase several of them at once. You can extend the period of use by cutting off the soiled layer of the sponge.
When soot and soot are completely removed, you can clean the surfaces of walls, floors and ceilings with aqueous solutions of detergents.

Abrasive powders should not be used. They spoil the structure of wooden surfaces.

On a note! Degreasing powders and/or gels are preferred. They are added to hot water.

To clean hard-to-reach areas, it is better to use a mop with a long handle.

Surfaces are washed 2-3 times. In this case, the water must be changed periodically, adding a new portion of detergent to it.

When the question of how to clean the lining in the bath from soot is resolved, you need to wash off the washing solution with clean water. For this, it is better to use running water. It is better to serve it from a hose under a little pressure.

At the end of the process, the washed surfaces are wiped dry with a clean soft cloth. You can use an old bath towel. From a large amount of moisture or with poor thermal insulation, the lining may turn black. In this case, the answer to the question of how to clean the lining in the bath will be a grinder, but this is if the darkening has affected only the surface layer of the wood.

To clean walls lined with clapboard, you will need an angle grinder with a power of no more than 1 kW and a petal circle with a diameter of 125 mm (grain size no more than 40 units). The lining is sanded in such a way as to remove the darkened layer to a depth of about 3 mm.

If the blackness has absorbed to a great depth, the lining can be painted. But not in a steam room. Here paintwork is not used at all. You can replace the darkened lining partially or completely with new material.

Impregnating compositions for bleaching darkened wood, prepared on the basis of chlorine, are not recommended, since the carbon particles that determine the dark color of the walls are practically not discolored by compositions containing active chlorine.

Unaesthetic dark spots appear on the surface of the bath logs from the outside over time, which spoil the appearance of the building.

Liquid bleach can be used to remove these stains. It is applied to the surface, previously cleaned of dust and dirt. For work, brushes with artificial bristles are used, which must be changed periodically, because the cleaning composition corrodes them. Before applying, you need to check its effect in an inconspicuous place.

The agent is carefully distributed over the entire surface and aged for some time according to the instructions on the package. Then you need to rinse the surface with running water from a hose. Next, the bath is ventilated to remove the strong smell of bleaching agents.

When blackening penetrates to a great depth, the logs can be sanded with a grinder. At the same time, safety precautions must be observed.

To clean the shelves in the bath, you can use a car wash. Water is supplied through it in a mixture with air and under high pressure. This helps to easily remove the top layer from the darkened wood. In this way, you can also clean the floors, walls and even the ceiling in the bath.

To thoroughly clean the floor in the bath, you can use a planer, best with an electric drive. Previously, the floorboards must be carefully removed and dried thoroughly, then treated with a planer. In this case, the top layer of wood on each side is removed to a depth of 5 to 10 mm.

As a result of this cleaning, sharp edges often appear on the floorboards. You can remove them with a belt or vibration grinder. You can also use these devices to clean darkened wood instead of a planer.

If the darkened layer of wood is thin, you can simply sand the surfaces with sandpaper. An electric drill with a special nozzle will help facilitate the process. You can work only with absolutely dry surfaces.

This method will help you get into corners and other hard-to-reach places. It is not necessary to remove individual elements.

Such treatment is often recommended when answering the question of how to clean aspen seats and other wooden surfaces in the bath. After processing and grinding with an emery skin, they will be not only clean, but also absolutely smooth.

Why does the chimney get dirty

How to clean the chimney in the bath depends on the nature of the pollution. With use, types of clogging may occur, such as:

soot and soot, which accumulates very quickly when burning household waste;
condensate, which is formed during irregular use of the bath;
foreign objects that accidentally fell into the chimney.

All of these types of pollution ultimately impede the free circulation of air and the exit of smoke through the chimney. This can cause carbon monoxide poisoning. A condensate is a weakly concentrated acid solution. Under its influence, the chimney masonry begins to collapse from resinous deposits.

With the constant use of the bath, it is necessary to draw up a schedule, determine in advance when and how to clean the pipe in the bath. Regular carrying out of such work will save the chimney and stove and allow you to use the bath without problems.

How to clean a chimney

The chimney and pipe in the bath are cleaned chemically and / or mechanically. Chimney cleaning liquids and/or powders can be purchased from a specialty store. Detailed instructions are printed on the package. After reading it, it will become clear how to clean the pipe in the bath.

A good answer to the question of how to clean the soot in the bath that has accumulated in the chimney will be a “chimney sweep log”. It is impregnated with special chemicals. During combustion, smoke of a special composition is emitted in the furnace. As a result, the soot becomes soft and pliable. After 2 or 3 days, it can be removed with brushes without much difficulty.

For mechanical cleaning of the chimney, you will need tools and devices such as:

rope and/or rope;
weight (ball);
ruff brush (preferably on a thin metal cable).

First you need to check the safety of the structure. Then you need to remove objects that accidentally fell into them from the pipe and chimney. For this, a brush-ruff is used, selected according to the size and shape of the pipe.

A special brush of modern design will facilitate the performance of cleaning work. It comes with a multi-piece handle. This allows you to adjust the length of the brush as needed. Any brush during cleaning work must be moved inside the pipe, gradually moving it lower and lower.

Such work must be performed in a special set of clothing, which must include:

overalls or suit;
respirator;
gloves;
protective glasses.

If the chimney is slightly dirty, you can invite a specialist. He will clean it with a special high-powered vacuum cleaner. This will remove soot from the chimney through the opening of the firebox. The use of special tools will solve the issue of how to clean the chimney from dirt, and how to clean the pipe from soot in the bath.

Tank cleaning

Due to the hardness of tap water, the question periodically arises of how to clean the tank in the bath from scale, which settles on the walls and bottom. Since scale is formed from lime deposits, it must be cleaned with acid.

Acid can only be used of organic origin. For example, lemon or vinegar. Any inorganic acid is not safe for the metal from which the tank is made. It should be remembered that the amount of acid used to clean the tank should approximately correspond in weight to the amount of lime deposits on the walls of the heating tank.

On a note! Installing a special filter on the inlet will help prevent the formation of a large amount of scale.

The water passing through it will be purified from a significant amount of impurities. This will greatly reduce the level of scale formation.

Cleanliness in the steam room

The steam room in the bath requires special attention. Indeed, when using brooms, particles of plant pigment from stems and / or leaves are absorbed into wooden shelves and walls along with moisture. Therefore, the question inevitably arises of how to clean the steam room in the bath to give it a fresh and pleasant look.

The problem of how to clean the lime lining in the bath, especially in the steam room, can be solved in different ways. In case of slight darkening of the wood, special liquid detergents and / or paraffin oil can be used.

The cleaning liquid is applied to the darkened surfaces manually using a piece of foam rubber or an ordinary sponge. The detergent must first be diluted with water. How to do this is detailed in the instructions.

Paraffin oil is applied little by little to pre-dried surfaces with a dry sponge. In this way, you can not only clean the lining in the steam room, but also give the wood water-repellent properties. This will protect wood finishes and various items from heavy and fast soiling.

Bath water purification

The necessary amount of water for hygiene procedures is often provided by drawing water from a nearby reservoir, well or borehole. Before use, it is necessary to thoroughly clean the bath water from various impurities, silt, sand, small pebbles.

The main methods of water purification are filtration and settling. A special water filter can be purchased at the store or made by yourself. To do this, you can use a fine mesh.

For settling, water is poured into a large tank about a day before the intended use. During this time, all impurities will gradually settle to the bottom of the tank. From above it will be possible to take clean water suitable for hygiene procedures.

The main rule: settled water should be taken from above, trying not to raise the sediment. Until the end of the water is not used. It is better to pour the remains into the drainage well along with the sediment. Therefore, it is necessary to prepare water with a margin.

Proper maintenance of the bath

To prevent strong pollution and the appearance of fungus, mold, woodworm, cleanliness in the bath must be maintained constantly. It is advisable to periodically treat internal surfaces with antiseptics to protect against microorganisms.

To prevent rotting of wooden coatings, it is necessary to apply special compounds to walls, shelves, etc. All wood surfaces should be inspected periodically. Elements affected by decay must be removed partially or completely.

After each use, the bath must be ventilated to dry the interior. Immediately after taking bath procedures, you need to clean up. This will remove all stains from interior surfaces before they soak into the wood.

On a note! An important point is the removal of leaves and small particles of the used broom from wooden surfaces.

They are removed with a special brush, sponge or cloth. After that, the shelves and other surfaces should be washed with warm water. This will help remove sweat, detergents, etc.

The remaining water on the floor must be carefully adjusted to the drain holes. When cleaning, pay special attention to the space under the shelves.

To prevent cockroaches or mice from starting, all leftover food from the rest room must be immediately removed and the garbage taken out. Bath accessories should be dried and laid out in storage places. The final stage is wet cleaning of all sections of the bath. General cleaning is also required from time to time. Proper maintenance of the bath will allow you to maintain an attractive appearance and cleanliness of the interior space, as well as the integrity of all coatings.

A wooden bathhouse made of logs or timber is a great place for a country house. Wood is distinguished by high thermal insulation properties, environmental friendliness and naturalness, safety. It does not heat up and does not burn the skin even at the strongest temperatures.

At the same time, the tree looks aesthetically pleasing and harmonious, fits into the environment. That is why wooden materials are chosen for the construction of a bath or sauna. However, natural raw materials are subject to the negative effects of moisture and insects. In addition, wood burns very quickly.

To protect wooden materials and extend the operational life of the building, the bath is processed. Today, there are many options and means that prevent the spread of fire on the surface in the event of a fire, rotting and destruction of wood, mold, fading and loss of physical properties. Let's look at how and how to process the bath from the inside.

How to choose the right tool

Natural wax, hemp and linseed oil are traditional processing materials that have not lost their relevance even now. These are safe and effective remedies. Today, manufacturers offer a lot of modern products that cover the walls in the bath and houses made of logs or timber. Experts advise choosing Finnish and Russian brands.

Choose products in such a way as to preserve the environmental friendliness of the building and emphasize the aesthetic interior of a log or timber bath. For a bath, especially for a steam room, you cannot use standard varnish or paint for wood, as they do not tolerate high temperatures. When heated, such products will emit an unpleasant odor and harmful toxic substances. In addition, with this treatment, the tree will not “breathe”, but will only absorb moisture and deteriorate.

Water and wax-based varnishes, as well as acrylic varnishes, are considered safe means for bath treatment. It can be colorless and colored products, with a matte or glossy sheen. For a steam room, it is better to choose a colorless varnish, and for a shower or rest room, you can take a product with a sheen or shade.

The vapor permeability of the varnish must be at least 50%. This indicator reflects the ability of water vapor to pass through the surface of the varnish film. Along with the steam, the smell of wood also passes. At the same time, the coating protects against moisture, which is not absorbed into the wood, but rolls down the wall onto the floor. As a result, the sauna atmosphere does not suffer, and the wood does not collect dirt and does not darken.

For the steam room, choose specialized odorless products. They consist of resistant components that do not break down under the influence of high temperatures. Classic antiseptics and varnishes are not retained in wood fibers, soften and become sticky at temperatures above 100 degrees Celsius. In addition, this process is accompanied by the release of harmful compounds and unpleasant odors into the air. Compositions for steam rooms are designed with these factors in mind, they are safe and environmentally friendly.

How to cover the walls and floor in the bath

Wooden walls in the steam room and washing room are covered with acrylic varnish or oil. The steam room is painted in one layer, the washing or shower room is covered with two or three layers. Suitable agents in this case are impregnations such as "Supi Saunasuoja" (Tikkurila) and "Pinotex Lacker Sauna" (Akzo Nobel).

Walls in dry rooms, for example, in a rest room, are recommended to be varnished or treated with impregnation for the interior. These waterborne coatings are odorless. In the MariSrub catalog you will find a wide selection of bath projects, including those with rest rooms, with a second or attic floor, as well as compact one-story buildings.

The floor inside the bath is least exposed to high temperatures, as hot air rises. However, the tree is most affected by water, as it flows down. The emphasis in this case is on protection against decay in a humid environment.

The floor logs are impregnated with a primer containing a powerful antiseptic, or varnished, which completely excludes the penetration of water into the tree. For this, a mold remedy, antiseptic "Pinotex Impra" (Akzo Nobel) is suitable. It gives the effect of preserving wood. The green color of this impregnation will not be visible under the finished floor, but the coating will provide long-term protection. To preserve naturalness, floor boards should be treated with shelf oil without the use of a primer.

In the rest room, locker room and other dry rooms, the floor is covered with parquet varnish. In the steam room and sink, the varnish is diluted in a 1: 1 ratio with a suitable thinner and the floor boards are impregnated. Apply two layers. After that, the bath is heated to a high temperature and the rapid polymerization of the coating is achieved. After airing and reheating, the bath is ready for use for its intended purpose.

How to cover other elements

It is very important to process benches, shelves and other pieces of furniture in the bath. This will increase the service life of products and prevent burns on the human body as a result of contact with hot surfaces. Water should not be absorbed into the wood, and at the same time, a varnish film is not needed on the surface of objects, which, when heated, leads to burning of the skin. Such a coating is given by special oils for shelves in saunas, including Supi Laudesuoja (Tikkurila) or Sauna Oil (Eskaro).

Lacquer, oil or other agent is applied in several layers using a roller. Difficult areas in the corners and between the crowns are treated with a brush. Each new layer is applied only after the previous one has completely dried! When using oil, excess product is removed before drying. Such processing should be carried out every 4-10 years, depending on the type of materials and the quality of the work. To get a long-term and reliable result, contact the professionals!

The masters of "MariSrub" will select high-quality and reliable impregnations, quickly and reliably process the bath. We provide a full range of services. It includes the design and construction of a bathhouse or a house with a foundation and a roof, the manufacture of lumber for the project, the installation and connection of engineering networks, and complex finishing. We offer warming and waterproofing of the bath, protective treatment of materials in several stages! We guarantee high quality of work and strict adherence to deadlines.