Choosing flooring for the apartment. Modern flooring for home and apartment The best flooring

Choosing the best floor covering

1. Linoleum

A variant from the "cheap and cheerful" series. The most affordable and inexpensive synthetic material. There are no restrictions in colors and patterns, it happens with or without insulation. It is customary to divide linoleum into three types depending on its strength: household, semi-commercial and commercial.If you decide to opt for linoleum, then take a semi-commercial one for your home: it is much stronger, although a little more expensive than a household one.By the way, the same story happens with the laminate, which will be discussed a little later: for the home, they most often take a laminate that is intended for public spaces.Linoleum can be laid in any home, except for cold ones: it will crack in severe frost.Pros:

• Does not rot, is not subject to the harmful effects of moisture With proper care, it has a long service life - over 10 years.
• Good soundproofing properties
• Easy care
• Lots of design and color options

Minuses:

• Linoleum is demanding on the base, it must be laid on a perfectly flat floor, then it will last a very long time. Otherwise, it will soon crack and "creases" will be visible.
• Non-environmental: linoleum is a completely artificial material, and noticeably loses in this regard to natural coatings.
• Low mechanical strength. Heavy furniture or even sharp heels can damage linoleum. Pets, especially large dogs, can destroy linoleum in a very short time.

2. Carpet and other carpets

Another inexpensive and very common flooring option. It is low cost, easy to install and does not require special care. Synthetic carpets are absolutely not interested in rodents and insects. Plus, there is a huge selection of colors and patterns, from classic "carpet" to radically avant-garde.Carpet can be used in any room except wet: kitchen, bathroom, toilet.Pros:

• Resistance to external influences - abrasion and various mechanical damage.
• Large selection of designs and colors
• High noise-absorbing qualities
• Excellent heat retention

Minuses:

Not resistant to fading and fading, especially in inexpensive types of carpet types. The need for regular dry cleaning. If you choose carpeting - take care of a good vacuum cleaner. Dust accumulation. Carpets are not recommended for people with a predisposition to allergies. Aesthetics (it is easy to deform)

3. Laminate

Laminate is the third most popular inexpensive and common flooring material. It consists of special panels made of fibreboard (MDF) and several layers of special thick paper. A pattern is applied to the paper (most often the texture of a tree is imitated) and a special durable protective layer of lamination. Hence the name - laminate.Pros:

Strength. Laminate perfectly copes with any mechanical load, scratches and so on. If you have pets, their claws will not be afraid of him. Laminate perfectly tolerates high temperatures, and is able to withstand short-term contact with fire (for example, with a match accidentally dropped on the floor). Laminate can be used together with underfloor heating systems, such as electric, and water. Affordable price. Laminate is more expensive than carpet or linoleum, but nevertheless, cheaper than many other types of coatings, for example, visually similar parquet boards

Minuses:

Fear of moisture. Despite its strength, the laminate is contraindicated in prolonged contact with water and other liquids. From prolonged contact with water, its fiberboard base will swell, and the laminate will become unusable. Short service life, despite mechanical strength. It is recommended to replace it every 5 to 7 years. Despite the apparent simplicity, laminate flooring is difficult to install without experience. It is better to hire professionals, and this is an additional amount to the cost of a laminate. It is easy to chip it, cause defects for a pattern. This is a huge minus, because a laminate, unlike a parquet board or an array, cannot be restored.

4. Floor board

Probably the most classic flooring option made from natural materials is wooden plank flooring. Solid wood flooring is expensive, but it is one of the most reliable and environmentally friendly types of flooring.Modern solid wood floorboards are made according to a special technology, dried and processed on special equipment. The boards have lock joints that simplify installation - the floor is obtained without gaps and height differences, as it was in the old grandmother's apartment.The floor from the array does not need to be painted: the boards are already ready for use, covered with pesticides and a layer of varnish.Pros:

Strength and durability. Solid wood flooring can last more than 50 years without the need to replace the boards. Such a floor can be scraped and sanded as many times as you like - the thickness of the boards allows this. Easy installation. Although, as in the case of laminate, you should not do it yourself - it is better to hire specialists. Good heat and sound insulation

Minuses:

High price. Solid wood is much more expensive than other types of wood flooring. Sensitivity to moisture: with prolonged contact with moisture, a board made of solid wood can "lead". Special protection against scratches is required. The massive board needs to be sanded, scraped and varnished annually. It is necessary to regularly treat with pesticides, despite the initial treatment.

5. Parquet and parquet board

Parquet from solid parquet boards is an expensive pleasure. Floors in royal palaces and very rich houses are laid out with such type-setting parquet. Modern parquet is cheaper, as it is made from composite materials: its base is thick plywood, and only the top layer of 3-5 mm is valuable wood.The parquet board has the same structure as the type-setting parquet: thick plywood with a thin face layer. Because of this, both parquet and parquet board today are quite affordable for people with an average income (cunning: take a three-strip parquet board, it is much cheaper).Pros:

Environmental friendliness. Parquet and parquet board are, first of all, natural wood. Adhesive based on natural resins is used as internal binders. Long service life. Good parquet can serve you up to 20 years. Parquet and parquet board perfectly retain heat. Appearance. Type-setting parquet can become a real work of art (there is a name for this - artistic parquet). Using parquet from different types of wood, you can create original ornaments and patterns on the floor. It can be restored (this is a definite plus, but it only applies to parquet treated with oil. It is more difficult to restore varnish, you will have to replace the whole board).

Minuses:

High price. And this is not only the cost of the material, but also the cost of laying work. If you want really high-quality parquet, you will have to spend money on a classy parquet floorer. Parquet is subject to mechanical damage, so it is not recommended to use it in a house with large animals - their claws will make the parquet unusable in a very short time. Parquet is afraid of moisture. And although it is less prone to warping than a solid board, it is not recommended to allow prolonged contact with water.

6. Engineering board

Engineering board is a relatively new type of coating. In fact, this is a parquet board, but made using a slightly different technology. An engineering board consists of two or three layers: a thick (up to 1 cm) layer of expensive wood, a layer of cheaper wood or plywood, and another layer of expensive wood (for a three-layer engineering board).Another difference between an engineered board and parquet is that it contains only water-soluble glue that does not contain toxins, while some inexpensive types of parquet can also use synthetic compounds.Pros:

Strength and durability. The engineered board is much stronger than ordinary parquet, its service life is longer - 20 - 25 years. The thick top layer allows it to be scraped and polished more times than parquet. It retains heat well. It is less susceptible to moisture than ordinary parquet. It is easy to install.

Minuses:

The price is still quite high: the cost of an engineered board is comparable to the cost of a good parquet. To lay it, you need to prepare a good, even base and a substrate made of plywood or fiberboard. Despite the increased moisture resistance, it is still not recommended to use an engineered board in wet rooms.

7. Cork floor

This is a natural coating with good heat-insulating and noise-absorbing properties, pleasant to the touch and easy to install. Made from pressed cork bark. It is produced in the form of plates and in the form of rolls.Cork flooring is perfect for a nursery, bedroom or living room. It is absolutely eco-friendly.Pros:

• Good thermal insulation. On such a floor, even in winter, you can walk barefoot - it keeps room temperature.
• Good soundproofing. In professional recording studios, for example, the floors and walls are necessarily finished with cork panels.
• Resistant to deformation. Heavy furniture does not leave marks on the cork floor - dents are leveled out on their own within a short time.

Minuses:

• Prices for material and the cost of installation work are comparable to the cost of laying parquet - not the most economical option.
• Cork flooring can swell and deform when exposed to water for a long time.
• It is not recommended to use indoors with pets: the claws will easily damage the cork floor. Also, do not walk on the cork floor in heels.
  

8. Ceramic tiles and natural stone

Surely in any apartment there is a room (and certainly not one) with a ceramic tile floor. Most often it is a bathroom, toilet, kitchen, less often a hallway. Durable, resistant to abrasion and not afraid of moisture, the tile is an ideal material for wet and walk-through areas.In principle, a ceramic or stone floor can be arranged both in the living room and in the bedroom, but in this case it is ideal to combine such a coating with a warm floor, otherwise your feet will simply freeze.It is probably not worth talking about the fact that the assortment of tiles and artificial stone is huge - in any, even the smallest hardware store, there are at least a dozen types of tiles for every taste and budget. This gives unlimited possibilities in terms of interior design.Pros:

• Affordable price. From the extensive range of ceramics, you can always find exactly the option that will suit you both in price and quality.
• Strength. When properly installed, ceramic tiles can last forever. An example of this is the ancient Greek temples, the floors of which are still finished with ceramics.
• Ease of maintenance. Ceramic tiles and artificial stone are perfectly washed, they are not afraid of moisture.

Minuses:

• Labor intensive installation. Laying tiles or artificial stone requires long and careful preparatory work.
• Seams between tiles. No matter how hard the master tries, the seams will always remain. It is necessary to close them carefully, and this is also a rather laborious process.
• The need to combine ceramic tiles with underfloor heating systems, and these are additional costs that increase the final cost of the coating.
  

9. Polymer coatings or self-leveling floors

Self-leveling floors have recently given way to more environmentally friendly materials - wood, cork or parquet, but still remain in demand. The reasons - the self-leveling floor is very durable, not afraid of moisture and provides unlimited opportunities for the implementation of design ideas.The material for such floors are cement-acrylic, epoxyurethane, polyurethane and epoxy compounds. In houses and apartments, the last two types are most often used. Self-leveling floors can be one-color, with a simple or three-dimensional pattern - the so-called 3D floors.Pros:

Self-leveling floors are not afraid of moisture, so they are most often used in bathrooms and kitchens. Properly made self-leveling floor can last up to 50 yearsResistance to fire and temperature.Ease of care.

Minuses:

High price. This includes not only the floor material itself, but also preliminary work on the preparation of the base, design, and so on. All this brings the self-leveling floor to the top price category. The quality of the self-leveling floor itself will depend on how well the rough preparatory work is done. The complexity of the replacement. If you get tired of the self-leveling floor, and you want to dismantle it, get ready for serious work and high costs.

The results of the hit parade

In our hit parade, we tried to briefly talk about all the most popular types of flooring that can be found on the market. Which of these do we recommend you choose?

If you are an adherent of eco-style and love experiments - try cork flooring. Love the classics and reliability - there is nothing better than a real solid wood floor or good parquet. Save, or do not want to invest a lot of money in a rented apartment - take an inexpensive linoleum, carpet or laminate .

In any case, you choose. And we will help make your choice easy and enjoyable. Live easy!

Owners of new urban apartments with rough finishes and properties that are about to undergo major repairs will not be able to get rid of laying the flooring. The interior design of the premises and the conditions for their operation, comfort in the house depend on it. An analysis of the operational and technical characteristics of the proposed materials will help determine which floor is better to make in an apartment.

The main types of floor coverings

When considering modern floor coverings for an apartment, property owners choose between the following materials:

• linoleum;
• ceramic tiles and porcelain tiles;
• laminate;
• piece or artistic parquet;
• cork floor;

All materials for the floor in the apartment are distinguished by a variety of designs, a long service life, and easy maintenance. The differences are in the laying methods, the complexity of the preparatory work, cost and practical characteristics.

Laminate or linoleum?

With a limited budget, the choice of the best flooring for an apartment is traditionally made between linoleum and. Linoleum is a classic solution, this material is easy to install, has a long service life and a variety of assortment. Manufacturers offer flooring for a room with any traffic intensity. The design of the collections impresses with its variety: the pattern of linoleum can be any - abstract, wood or tile, metal or parquet, natural stone or pebbles. The main advantage of the material is the ease of installation, the work can be done independently, without the involvement of specialists.


Laminate is a trend of the last decade, this material is presented in different price categories, can be used in underfloor heating systems and is distinguished by a variety of collections. Manufacturers offer a waterproof laminate for the bathroom and kitchen, created from PVC. Laying the flooring is done using a simple tool, but requires an even base and care during work. Be sure to use a substrate that compensates for small flaws in the base and improves sound insulation.
When choosing what to make a floor from - from linoleum or laminate, it is necessary to evaluate the quality of the base.

An uneven screed will lead to the fact that the locks of the laminate will begin to break, cracks will appear in which water will get into. An ideal base and a competent choice of laminate in terms of abrasion class is the best solution for budget repairs. Linoleum is indispensable when there is no way to improve the quality of the screed. The foam base of this flooring is able to compensate for small flaws in the subfloor.

Which floor is better to make in the apartment: parquet, parquet board or cork?

When deciding what to put on the floor in the apartment, fans of environmentally friendly materials choose between piece parquet, cork flooring and parquet board. For elite urban apartments, these floorings can be competed with artistic parquet, which is distinguished by its exquisite design and high cost.


Parquet and cork panels are an expensive floor covering for a room, the choice of which should be taken with special attention. Piece parquet is made from solid wood of the best grades. Its service life exceeds 50 years, the material is not afraid of high loads, and sanding can restore its ideal appearance during scheduled repairs. The disadvantages of the material include its cost and the need to involve specialists in laying.

Cork flooring is available in two types - tiles and panels with a lock. For self-installation, the question: which flooring is better is rhetorical. Cork veneer tiles must be glued to an ideal surface and then varnished, like parquet. The lock cork flooring is laid according to the laminate principle and this work can be done without the involvement of craftsmen.

Parquet and cork compete with parquet board - a compromise solution not only in terms of price, but also in terms of quality. The panels of this material resemble laminate, have a locking connection and are easy to install. Unlike parquet or solid board, the thickness of expensive wood species is only 4-6 mm, which reduces the cost of the material. The basis of the parquet board is a beam of softwood, glued perpendicularly to a thin pine veneer. This design guarantees the strength, durability of the floor covering, meets strict environmental standards.


When deciding what is better to lay on the floor - parquet or parquet board, tiles or cork wood panels, you need to be guided by your budget. All materials are environmentally friendly, with an individual texture and a long service life. Cork parquet and tiles are suitable for exclusive interiors, parquet board and cork wood panels are the best solution in a classic style.

Moisture-resistant floor in a city apartment

When analyzing which flooring to choose for a kitchen or bathroom, you need to consider the likelihood of puddles on the floor. A spilled pot, a malfunctioning dishwasher, or a disconnected water heater hose can cause puddles to form on the floor. Water is the main enemy of wood, laminate, cork. It is for this reason that there are reliable moisture-resistant floor materials - ceramic and clinker tiles, porcelain stoneware, self-leveling floors.

Ceramic tiles are distinguished by a variety of assortment and affordable price. This is the best choice for small rooms with high humidity. The competition for this material is clinker tiles and porcelain stoneware. They are highly resistant to abrasion, strength, frost resistance. Deciding what is best for flooring in the garage, the choice is stopped on clinker tiles, as it does not absorb engine oil. In a city apartment, you can use any option, thanks to the impressive variety of collections.

The tile material competes with the self-leveling floor, which is distinguished by its durability, strength, and water resistance. Material suppliers offer exclusive solutions for any interior. The only drawback of self-leveling floors is the high cost and the need to attract qualified specialists.

Choosing a floor for different rooms

When choosing a floor covering in an apartment, it is difficult to determine what is best for all rooms. All rooms differ in traffic intensity, air humidity, environmental requirements. It is not difficult to give an answer to a rather simple question - to cover the floor in the kitchen, which is better ceramic tiles or parquet - and it is problematic to choose between linoleum and laminate in the living room. It is necessary to take into account the quality of the subfloor and the qualifications of the master.

Depending on the purpose of the rooms, it is worth choosing between the following materials:

• entrance hall - semi-commercial linoleum, laminate 23 or 31 class, cork flooring 23 class, ceramic tile or porcelain stoneware;
• bathroom and toilet - ceramic tiles, porcelain stoneware, PVC-based laminate, self-leveling floors;
• kitchen - ceramic or clinker tiles, porcelain stoneware, PVC-based laminate;
• living room - laminate 22 or 23 class, cork, parquet, parquet board, linoleum;
• children's room - cork flooring class 23, parquet board, parquet;
• bedroom - laminate, parquet board of small thickness, parquet;
• balcony or loggia - linoleum, ceramic tiles, porcelain stoneware.

For bedrooms and children's rooms, the environmental friendliness of the materials used is important, the bathroom and kitchen are demanding on the moisture resistance of the coating. Abrasion-resistant materials are used in the hallway of a city apartment.

Often, property owners ask themselves: what is better to use for underfloor heating? These heating systems are popular, the best choice for them would be ceramic tiles, clinker or laminate. When using parquet or parquet boards in rooms with underfloor heating, you should refuse collections of hornbeam, cedar or maple and give preference to teak or merbau. In this case, the flooring will last as long as possible, and its exterior will remain flawless.

Vinyl Flooring: Features and Benefits

If parquet seems to be an expensive pleasure for someone, then, for sure, they will see a worthy alternative in vinyl flooring. He is credited with many of the positive features that characterize wood flooring and linoleum. At the same time, there are no bad sides of vinyl that competitors have. The owners of an apartment or a private house get the opportunity to decorate any interior by choosing the best solution with a vinyl coating.

The structure of vinyl flooring and its advantages

The production technology provides for the inclusion of polyvinyl chloride, chemically inactive fillers, crushed quartz and some other components in the composition of the material. A decent look and proper shape are given by pressing at high temperatures. Synthetic components should not cause concern that during operation they can serve as a source of toxic substances, thereby posing a potential threat to the health of the inhabitants.

If you look at the cross-sectional plane of the vinyl coating, the following layers can be distinguished:

1. At the very bottom is a layer of polyvinyl chloride. It is attached to the base of the floor. The polymer strengthens the vinyl flooring.
2. Above is a reinforcing fiber layer of woven glass strands. Thanks to him, any kind of factors acting from the inside and outside are not able to change the shape of the product.
3. The so-called interlayer, which consists of quartz and sand, also reinforces the structure.
4. Decorative film. The topmost layer is also represented by a polymer - polyurethane. First of all, it is entrusted with the task of preventing the destruction of the product in the event of moisture, mechanical stress or ultraviolet rays. Sometimes there are modules with a convex surface or a surface on which the sole does not slip. On the other hand, decorative film is designed to give the impression that the floor is covered with stone, wood, leather, etc.

Advantages and disadvantages of vinyl flooring

Benefits of vinyl flooring:

1. From all the huge colorful variety, you can choose the color or pattern of the coating in accordance with your design tastes.
2. Many of those who have a vinyl floor for a long time, for sure, were convinced of its practicality. The original appearance almost does not change, the surface is not scratched, and when light objects fall on the floor, dents do not form.
3. Vinyl is comfortable in wet environments. Therefore, they can safely cover the floor in the bathroom or kitchen without fear.
4. There is no need to use chemicals to restore a well-groomed appearance. It is enough to wipe it with a cloth dipped in plain water.
5. Outwardly, the design seems to be monolithic, there are almost no seams on the floor - the elements are so tightly adjacent to each other.
6. With the installation of vinyl, as well as this repair, almost every owner will cope with minimal professional skills.
7. Even if you walk barefoot on vinyl flooring in winter, it will not seem cold to your feet.
8. Vinyl flooring is cheaper than some of the other options.

Disadvantages of vinyl flooring:

1. High requirements for the base of the floor - it must be even and clean. Otherwise, the vinyl coating will wear out or deteriorate before the operating period allotted to it by the manufacturer.
2. Toxins are distributed only when the material, through the negligence of the owners, catches fire.
3. Taken to a landfill after dismantling, the old vinyl coating will lie there for decades, without decomposing into simple components.
4. If, for example, in a bathroom, a rubber mat is placed on a vinyl floor, then after a while a stain forms under it - prolonged contact with rubber, the polymer reacts with discoloration or pallor.

Vinyl Sizes

Rectangular tiles 600 mm long and 300 mm wide. In addition to the usual vinyl tiles, there is a quartz-vinyl version on sale. In the latter case, the floor covering is more resistant to chemicals and mechanical stress, an excellent insulator in relation to electricity. Quartz-vinyl tile has proven itself well in those rooms that will be frequently visited by people.

Roll cover. In each such roll, the canvas is from 15 to 20 meters long and 2 meters wide. Suitable for use in large rooms.

Laminated modules, each of which is a plate stretched up to 920 mm in length and 100 mm or 180 mm wide. A ball of fiberglass or felt that is in direct contact with the base of the floor plays the role of a shock-absorbing substrate, softens sharp mechanical loads when walking. The smallest thickness is 1.5 mm. The pattern on the front side gives the vinyl flooring a resemblance to a wood structure or makes it hard to distinguish from real bamboo in appearance.

Methods for installing vinyl floor coverings

Actually from the name "adhesive" the essence of the installation is clear - with the help of glue, which is usually applied with a spatula. It is convenient to press down to the base of the floor with a roller.

Locking modules assume the orientation of two plates to be joined in such a way that the spike of the first of them enters the groove of the other. The end result is a really secure connection like a lock. This method is good in that no additional fixing means are required during installation.

Self-adhesive vinyl tiles have an adhesive layer on the back under an easy-to-remove film. The film is needed to prevent the adhesive from drying out. It is removed immediately before laying the tiles on the subfloor. The laid tiles are pressed by rolling a rubber roller.

Tsugunov Anton Valerievich

Reading time: 6 minutes

Every person wants his apartment to be cozy, comfortable and beautiful. In solving this problem, the choice of flooring plays an important role. And since the floors in the apartment are under serious stress, the selected material should not only be attractive, but also meet the requirements of safety, durability and ease of maintenance. Consider the most popular flooring options and find out which one is best suited for laying in an apartment.

Today's market for flooring materials is replete with variety. Parquet, laminate, linoleum ... Which one is better is a difficult question.

All coverages can be divided into three conditional groups:

1. Wooden - parquet and parquet board, solid wood, cork, laminate.
2. Elastic - linoleum, carpet.
3. Ceramic or stone - ceramic tiles, porcelain stoneware, self-leveling floors.

wooden group

A place of honor among the materials for finishing the floor is occupied by floor coverings, in the manufacture of which wood is used.

Parquet is a classic flooring material. It has not gone out of fashion for many years and is an indicator of the well-being and excellent taste of the owners of the apartment. Today's parquet looks like a ready-made shield of a fairly large size, made of precious wood with a pattern already on it. There is also piece parquet. From it you can lay out unique compositions. It is most often made from durable wood species:

• from oak;
• beech;
• maple;
• ash.

Whatever type of parquet is chosen, with proper care it will last at least 50 years.

Parquet is environmentally friendly and completely safe, but it obliges to prepare a high-quality subfloor, refers to expensive materials and requires maintaining a certain temperature and humidity in the room.

For the manufacture of parquet boards, natural wood is also used, but each lamella is not a solid piece of wood, but a firmly glued three-layer structure. Such a coating will cost less than parquet, it is easier to install and maintain. Parquet boards are presented in different shades, they can be combined and composed. This type of floor will last about 15-20 years.

Solid wood flooring

Floors made of ordinary wooden boards laid on logs do not lose their popularity. Despite their apparent simplicity, they have many advantages:

• 100% environmental friendliness;
• accessibility, practicality;
• the ability to create an interior room in a certain style;
• this floor is pleasant to the feet and looks great.

With proper care, this coating will delight the owners for about 30 years.

Cork

Cork coverage is close to ideal:

• It is natural, warm, strong enough, pleasant for the feet and good for health.
• Cork floors come in a variety of shades, which allows you to create interesting compositions.
• This material does not accumulate static electricity at all.

The cork can be coated with special oils and varnishes, or it can be used without coating. The service life of cork floors is from 5 to 20 years.

Important! Keep in mind that with a strong mechanical impact, traces may remain on the cork floor.

Laminate floors

Laminate flooring is gaining more and more popularity due to its outstanding characteristics:

• It is affordable, practical and quite reliable.
• Laminate perfectly conveys the color and texture of natural wood, stone, tiles.
• Laminate boards are equipped with a locking system.
• Even a novice in the repair business will cope with laying such a floor.

Laminate has several strength classes. The higher the class, the stronger and more expensive the material.

Elastic coatings

These include two materials: linoleum and carpet.

It is the absolute leader among floor coverings:

• affordable;
• easy to install and maintain;
• absolutely not afraid of moisture;
• looks beautiful.

Linoleum can have a wide variety of shades and patterns, sold in sheets rolled up or in the form of tiles. Such a coating is attached to the base floor with special adhesives. After 5-10 years, it will have to be replaced.

It can be called a relative of the carpet, which has its own characteristics:

• The composition of the carpet can be both artificial and natural fibers.
• Sold in rolls or as carpet tiles.
• It is very easy to install and attaches with glue.
• Diverse in texture and color, safety.

The disadvantages of such a floor covering are a relatively short service life, lack of moisture resistance and difficulty in cleaning and cleaning.

But they also have disadvantages:

• The coating is hard, traumatic and cold.
• It is better to mount heating systems under it, otherwise it will be uncomfortable to walk on the floor without shoes.
• Before laying, special preparation of the base is required.

self-leveling floor

Modern self-leveling floors are used not only as a rough screed. They can be an excellent finish and contain highly artistic three-dimensional drawings and a variety of decorations under the polymer layer. Self-leveling polymer floors are:

• epoxy;
• polyurethane.

Both materials are environmentally friendly and durable, they are not at all afraid of water and other liquids, they do not require any special cleaning.

The disadvantage of this type of flooring is the special demands on the surface on which it is laid. The base under them should be perfectly flat, dry and clean.

Important points when choosing a coating

Each person decides how to make the floor in the apartment. But when choosing a material, one should not miss a few fundamental points.

The main criterion for choosing a coating is the room in which it will fit. The whole apartment can conditionally be divided into zones:

• an area for receiving guests and relaxing (these are bedrooms, a living room, a children's room);
• "wet" area (kitchen, bathroom);
• passage area (entrance hall, corridor).

For each of these zones, it is necessary to choose your own material based on their functional features and the loads that the floor carries.

• The choice of gender is influenced by the lifestyle of the family and its composition. What is suitable for a single married couple is not always suitable for a family with children. When there are children in the house, the floor should be safe, hygienic and easy to clean. The coverage must meet the same requirements if there are animals in the apartment.
• Financial security also plays a role. For example, floors made of natural materials are quite expensive. Families with limited incomes will most likely not be able to afford them.
• An apartment located on the ground floor will limit the choice of flooring due to its high humidity and proximity to the basement.
• In some apartments, it is impossible to make the floor heavier due to the formation of an additional load on the interfloor ceilings. Therefore, floors that require a concrete screed device will have to be abandoned.

Glossy tiles will not fit in the hallway. When snow gets in, it becomes very slippery, which can cause injury.

Linoleum is also a good option for the hallway, the main thing is not to dwell on its cheap varieties. It is better to choose a material with a natural composition, commercial or semi-commercial: such coatings can withstand almost anything.

If the choice fell on a laminate, you need to pay attention to its strength class. For the hallway, coverage from class 32 is suitable.

How to make the floor in the bedroom

What floor should be in the bedroom? This question is faced by everyone who makes repairs in the apartment. The bedroom is a relaxation room, here most often they go barefoot. Therefore, the floor should be warm, pleasant to the feet and beautiful.

• From natural coatings, solid wood, parquet and cork will perfectly cope with these tasks.
• From the arsenal of synthetic materials, carpet is perfect. It is pleasant to the touch, walking on it is soft and comfortable. In addition, it has good sound insulation, which cannot be achieved from other artificial materials.
• Laminate is also often used for flooring in the bedroom. It is durable, beautiful, but it is not very pleasant to walk on it with bare feet, so it is better to put small rugs on the floor near the bed.

Whatever material for the floor is eventually chosen, let it please the owners with its appearance for many years.

(votes: 2 , average rating: 3,50 out of 5)

Floors and walls in the apartment play an important role. But it is the floor coverings that set the stylistic design and perform the function of sound insulation, and also help to retain heat. Therefore, it is important to know how to choose the right quality flooring.

Peculiarities

The temperature regime in the room, as well as some characteristics of the room, will depend on the choice of floor material. In addition, the flooring greatly affects the stylistic design of the room. Therefore, when choosing, you should weigh the pros and cons of each floor covering and choose the most suitable for each specific area.

The floor covering allows you to set the basis for the aesthetic design of the premises. In addition, it makes the room more cozy and comfortable for residents. The choice of floors varies depending on the purpose of the premises, since the individual functional areas of the apartment involve different loads and effects on the floor. That's why it is better to consider all the options, and only then make a choice in favor of one or another option.

The specifics of floors for an apartment may vary depending on the floor. For the first, it is better to choose a moisture-resistant coating. For high floors, floors with a light texture are needed. If you are installing flooring in a panel house, then pay attention to models with thermal insulation and sound insulation characteristics.

An important feature of laying floors is additional base. Some materials require a special leveled subfloor or even a subfloor, while others can be laid over plain concrete floors.

Also, some apartment residents prefer insulated floors, while using different insulation technologies and substrates for coatings.

Kinds

Floor coverings are hard or flexible. Separately, a group of wooden floor coverings is distinguished. Different manufacturers represent a variety of types of flooring, which differ in their functionality, quality and design. Wooden ones include:

• parquet;
• parquet board;

• laminate;
• wood mass;
• cork.

Flexible coatings include:

• linoleum;
• carpet.

Hard surfaces include:

• ceramic tile;
• stone floors;

• porcelain stoneware;
• expanded clay;
• bulk floor.

Each type of flooring should be discussed separately, since they all have important characteristics and properties.

Natural parquet

This is a classic version that is traditional and very popular. This classic never goes out of style. This coating will emphasize the high social status of the owners of the apartment. Parquet is made only from valuable tree species.

As a rule, parquet elements have a natural wood pattern. You can find small-sized versions of piece parquet. They allow you to lay out an interesting composition.

So, with the help of it, you can independently make a drawing on the floor, for example, a Christmas tree.

Parquet is made from durable and reliable species, the wood of which is characterized by high density. For its manufacture, oak, beech, maple, ash, larch are used. This flooring is considered the most durable. It can last up to 50 years if you take good care of it.

Any parquet is completely environmentally friendly and completely safe. A feature of the installation of such a floor is that under it it is necessary to install draft floors. Only after that it will be possible to lay piece parquet.

Not all apartments can be parquet. An important requirement is compliance with a certain temperature regime and the level of air humidity.

Parquet is a very expensive and noble flooring option.

parquet board

This is another option for natural wood flooring. The parquet board differs from the previous type in that it is quite large in size. The difference is the composition of such boards. Thus, parquet board lamellas consist of three layers, securely connected to each other. They have convenient lock fasteners and are easier to install. Their size allows easy installation and easy dismantling.

Manufacturers present models of various colors and designs, some of them have a ready-made pattern. It is easier to care for a parquet board than for piece models. Such a coating is quite expensive, but more budgetary than piece parquet. The slats can serve over 20 years Besides, they are not so whimsical in care.

Boardwalk

Such floors involve laying ordinary boards on logs. It looks simple but natural. It is used in apartments infrequently, because it is quite heavy. But the big advantage of plank flooring is that it is 100% environmentally friendly and very practical. With it, you can create interesting stylistic solutions for rooms.

The floor is pleasant to the touch and comfortable to walk barefoot on. Plank flooring is more affordable. At the same time, according to external characteristics, it is not inferior to other options for wooden floors.

photos

Cork

Cork floors belong to the elite floor coverings. They are suitable for laying in almost any room, except for rooms with high humidity, such as a bathroom, if there is not good ventilation. But the cork can only be laid on a hard and even surface. Most often, plywood is installed under it. Under no circumstances should it be laid on bare concrete floors., otherwise even small particles can ruin the flooring.

The cork can be decorative. It is presented in the form of rolls or plates. The top layer is impregnated with a special composition that has moisture-proof properties. Manufacturers supplement the cork floor in the form of slabs with an adhesive that has already been applied, which simplifies the installation of this floor covering.

Cork is also used as an option for the subfloor. It is placed under linoleum or under laminate. In this case, it has a slightly different composition and significantly reduced quality. As a rule, cork provides the necessary level of heat and sound insulation. Such a substrate can be presented in the form of rolls, it is convenient to spread it on the floor.

The cork floor can be presented in the form of MDF panels. As a rule, these are rather large lamellas, which include other materials, including synthetic ones. Each panel measures approximately 19 x 90 cm. They are comfortable and easy to lay on their own. Installation is facilitated by lock fasteners.

Cork is a practical material because it is completely immune to temperature changes.

In addition, it withstands high physical loads and impacts. Even the heaviest furniture can be placed on it. Cork can be quite interesting in design thanks to modern production technologies. Manufacturers present models of different shades. In addition, it is not a static material on which dust and hair do not accumulate.

Laminate

This is a high-quality and reliable floor covering that can imitate any other types of floors. It can be an imitation of parquet, natural boards and other wood, tiles, marble, natural stone and even brick. The slats can have different sizes, but the standard boards are 25 by 150 cm. The slats have a lock, which, as a rule, is located either on two or on all four sides of each board.

These lamellas are easy to install and maintain. By itself, the laminate board includes four layers. Each of them has a specific functional purpose. Together, they all make up a high-quality and reliable option for flooring.

The bottom layer is paper soaked in resin, which performs a moisture-proof function. Thanks to this, the laminate board will not be damaged during a flood. The lower substrates of some models can also perform a heat or sound insulating function. No sills are needed to cover.

The penultimate layer is the most basic and thick, on average, its thickness is from 5 to 9 mm. It is a compressed wood, as well as locks built into this level, which are based on spikes and grooves.

The next layer is decorative. It is a patterned coating that imitates wood and other materials. From above, it is covered with a transparent layer, which makes the coating more beautiful and decorative. In addition, it performs protective functions and prevents rapid rubbing and damage to the laminate. As a rule, the transparent layer is made of acrylic or melamine.

Laminate is an affordable yet practical material.

It perfectly conveys the texture of many materials and looks very aesthetically pleasing. The marble version looks elegant.

Laying this floor option is within the power of even a beginner in the field of installation. Laminate can be divided into classes depending on its strength. The higher the grade, the higher is its strength and thickness. Most often, for domestic purposes, options from 21 to 33 classes are used.

Linoleum

In Russia, this is the most popular flooring. It is very easy to install and yet affordable. Almost no maintenance required, it is enough only to periodically carry out wet cleaning. The material is completely moisture resistant and not subject to external influences. Such coatings can look very beautiful.

Manufacturers present a variety of options that differ in their pattern and shades. As a rule, these floor coverings are sold in the form of rolls. It is enough just to roll them on the floor. There is also a slab option.

Linoleum is mounted using a special adhesive, and it can be installed on almost any floor. In the manufacture of linoleum, both natural materials and polymers are used. Models with natural substances in the composition are more expensive, therefore less popular. The service life of linoleum is approximately 10 years, but it is most often used in apartments for much longer.

Linoleum can be thin, or it can be insulated with a backing. Foam-based options are also popular. But such a coating has several disadvantages. So, it can shrink and change its external qualities when exposed to elevated temperatures. In addition, heavy furniture leaves traces and damage on it.

Linoleum can be laid in absolutely any room, even in an unheated one, for example, on a balcony.

photos

carpet

Outwardly, it is a covering similar to carpets, which differs from other floor coverings in a number of features. Models can be soft or quite hard to the touch. They are often placed in children's rooms, since they are not at all traumatic. In their manufacture, manufacturers use both natural and artificial materials.

The coating can be presented in the form of rolls or tiles. Sheet models are easy to mount on their own without assistance. Only glue is needed for installation. The material looks very presentable. Manufacturers present options that differ in their texture, pile length, color and pattern.

But this coating, with external presentability, has a number of negative properties. Yes, it has short service life. In addition, it is considered the most not waterproof of all floor coverings. It requires special care and systematic cleaning, otherwise the coating will lose its former gloss. The basis of the carpet is jute, felt or rubber.

Such a coating is completely unsuitable for floors in the hallway or bathroom. Some stains may be impossible to get rid of.

This option is not suitable for allergy sufferers, as it can provoke an allergic reaction.

Ceramic tile

This is a very dense and solid option, which involves flooring only in some areas of the apartment. So, they put it in the bathroom, toilet, hallway, kitchen, corridors. This coating is cold, so it is not suitable for other rooms. But if you plan to install underfloor heating, then in other rooms you can make flooring in the form of tiles.

Ceramic tile is a versatile option that has a number of advantages. It can be placed on any floor, including on concrete, wood, plywood, drywall, soil. Ceramic tiles can have different designs and patterns.

This floor is suitable even for classic style interiors.

Tiles can be matte or glossy. Due to its texture, this material is able to hide dust and dirt. In addition, it is quite easy to care for her. It is waterproof and practical.

Manufacturers present corrugated tiles that you can step on with wet feet. That's why This cover is perfect for the bathroom. You won't have to worry about slipping.

The color scheme of this finishing material can be absolutely any. The tile itself is very strong and durable. These are high-quality vapor barrier and non-combustible floors. The tile is attached with glue and lasts a very long time. But the coating is solid, so it is traumatic. It is not comfortable to walk barefoot on cold tiles.

self-leveling floor

Previously, such a coating was most often used as a subfloor, while new self-leveling floors are excellent decorative coatings. The design assumes the presence of three-dimensional drawings and patterns that are covered with a polymer layer. Bulk floors can be polyurethane or epoxy. By themselves, they are of high quality and environmentally friendly.

The service life of such floors is quite long. They can look very presentable, especially for glossy models with patterns. These are waterproof and easy to care for. Their disadvantage is that before laying, you need to perfectly level the surface and dry it otherwise, irregularities may appear.

Which ones to choose?

The choice of flooring is a very important part of any renovation. In this case, one should take into account in which functional area or in which room it will be located. For each of the zones, you need to select materials based on what qualities they have and what loads they can endure. In addition, family composition should influence the choice of sex.

Some coatings are completely unacceptable for children. If you have small children, then the floors should be less traumatic and completely environmentally friendly. In addition, such floors should be easy to care for. If you have pets at home, then the coating must withstand mechanical stress, such as scratches.

When choosing, you should also evaluate your financial condition, since some flooring options are very expensive and require special care. If your apartment is on the first floor, then you should purchase the most moisture-resistant materials. This is because the closer to the apartment the basement, the higher the level of humidity in it.

Not all apartments can install some types of coatings. So, in panel apartments it is not always possible to insulate the floor, since an unacceptable level of load on interfloor partitions may occur, this is permissible only in good new buildings or private houses. Thus, you will have to choose models that do not require a concrete screed.

As for individual rooms and functional areas, there are a number of requirements. So, the hallway area is always the most accessible and dirty. It involves a large load on the floor covering and many external influences in the form of moisture, dust and dirt. If you have children, then you will put strollers and children's sleds there, which can damage the coating.

That is why only the most solid and high-quality option is suitable. Moreover, it should look presentable and complement the interior of the apartment as a whole. The most acceptable for such premises will be ceramic tiles. It serves for a very long time and endures all of the above effects.

Linoleum is also often placed in the hallway, but at the same time, the hardest models with an additional substrate are acquired. Another option for the hallway is laying laminate flooring. But in this area of ​​\u200b\u200bthe apartment it is better to select durable models of class 31-33.

For the bedroom, you can choose other floor coverings. Considering that it is in this room that you will most often walk barefoot, therefore, the coating should be warm and pleasant to the touch. For this, parquet, parquet board is perfect.

The carpet is very soft and aesthetic, so it is ideal for the sleeping area. At the same time, it performs well the function of sound insulation, which is so necessary for sleeping quarters. Laminate can be laid in this area, but rugs will have to be placed near the bed, because without a substrate in the form of warm floors, the laminate is cold.

Work technology

The floor of the apartment has two layers - intermediate and directly flooring. In the thinnest prefabricated houses, there is no intermediate layer, and the flooring is laid on a bare surface. For this option, when laying with your own hands, it is necessary to smooth the DSP before installing the grout. To do this, it is better to use the thinnest layer of cement screed - the so-called "pie". So you can increase the level of noise and heat insulation.

When repairing the floor, wooden beams are also used as a base. So you can make heat and sound insulation. From above they can be covered with a layer of insulation from moisture. An intermediate layer is placed on the floor. It may consist of a log, a subfloor, additional insulating and waterproofing substrates, a thin concrete screed. And already on top of these layers, you can lay the floor covering.

If you choose a wooden floor from boards, then it is already placed on beams without a subfloor. In their quality, reinforced concrete products, timber, metal profiles are used.

When repairing, the cement screed method is often used. This is one of the easiest types of installation. At the same time, a special cement mortar is made. Initially, the surface of the floors is cleaned from old concrete. After that, the floor is cleaned of dust and dirt. Then it is important to measure the slope and calculate the required volume of cement mortar. You can buy a mixture ready-made or make it yourself.

After you have received the finished solution, you need to mix it well. Then you can set beacons and guides that will allow you to fill the floors well and evenly. Cement must be evenly distributed over the entire surface and smoothed to the desired level. The preparation of the base must be carried out, while it is still damp and not hardened. This is necessary so that the floors last longer and do not crack. The screed dries out for about 30 days.

Another option is laying a semi-dry screed. This option dries out much faster and at the same time better protects against moisture and does not release heat. There is much less water in it and there are special fibers that prevent cracking. The technology of its laying is approximately the same as in the previous version.

You can also use the dry screed method. On such a floor, you can put a coating immediately after installation. Polyethylene sheets must be placed on the floors, and then covered with sand and leveled. The layer must be compacted and covered with a metal profile. This method is suitable when laying on a strip foundation. Gypsum boards are laid on top and fixed to the profile. On such a screed, you can immediately mount any floor covering.

Warming

Floor insulation involves fixing wooden logs to polyethylene. Styrofoam or mineral wool is laid there. The thickness of such a layer can vary from 5 to 10 cm. From above, this heat-insulating level is covered with plywood or a board, and a decorative coating is already applied on top.

Another option for insulation is a dry screed. This is a quick and effective way to insulate the floors in the apartment.

The substrate is also a fairly popular way of warming. It involves laying sheets of foamed polyethylene under a decorative coating. This is not the most efficient, but very easy to install method. Since the substrate is quite thin, it allows you to keep air and does not let it through between the plates or lamellas that make up the decorative coating. It involves a little soundproofing and insulation. As a rule, such a substrate is used in combination with other protective measures.

As a substrate, special cotton wool or other materials are often used. They do a good job with the function of heat and sound insulation. These heaters may include cellulose, noise plastic, rubber, acrylic elements and expanded polystyrene.

Another option for the substrate is the laying of extruded foam. It can even be placed on concrete. To achieve the best effect, the substrate is placed in several layers. From above, you can use flooring from any decorative coating. It is better if it is of high quality and durable.

Beautiful examples in the interior

In a modern interior, you can make a light floor from parquet or laminate. It is perfect for Provence and Classic styles. The shade of bleached oak will be suitable. You can complement it with a rug in the form of an animal skin.

For apartments in the style of a classic or modern, a parquet brown floor under wenge or oak is perfect. This cover looks noble and elegant.

We will analyze the most popular coatings, and you will already decide which of the evils is the least.

First, take into account the initial data of the kitchen

Before thinking about what is better to put on the floor in the kitchen, you need to think about where exactly the room is located:

1. If we are talking about a high-rise building and a middle floor, then almost any floor will be warm enough and it makes no sense to especially worry about warming.
2. A if you live on the ground floor or in a private house, then here the conversation is different, since in winter, without special heating, the floor can be simply icy.

Also important is the initial humidity of the room, which, again, depends on the location. Particularly wet kitchens are on the ground floors and in houses without a basement. Having laid a wooden floor in such a kitchen, for example, you should not count on the fact that it will lie for a long time and will not need scraping.

But let's go in order.

What floors are there and which ones are the most practical?

Of the most popular and affordable coatings today, we can distinguish:

There are, of course, also cork floors, there are stone ones, but this is no longer so popular, since the price “bites”. Therefore, we will not include them in our review, it is better to talk about them separately, taking into account all the nuances.

From all of the above, we can say that the most practical floors are tile and self-leveling.

But the tile has one big minus - it is cold. Self-leveling floors are quite expensive. But we are all Let's look at it in more detail in separate blocks. considering both advantages and disadvantages.

If desired, you can also make a combined floor, this is especially true for kitchens connected to the living room. Due to the transition of textures, it is possible to successfully zone the room.

About screed and insulation

When repairs are in full swing, the question of which coatings to prefer is not the most burning one. Now the main thing is the screed and leveling of the surface.

Before choosing the material from which the screed will be made, you need to think about what you will lay on top.

If it is a tile, then there is no difference what will be below and an ordinary cement mortar will do. And if it is a laminate, then it is much better to make a gypsum screed using a plaster mixture for this. Such a floor will come out much warmer and will be less moisture permeable.

Also, the thickness of the screed may depend on what type of insulation you choose.

And if you raised the screed high enough, then making wooden flooring is no longer very reasonable if your ceiling height is standard, that is, 2.5 meters. If you "steal" the extra 10 cm, then this will significantly affect the visual perception of the room.

And if you are also planning a hinged ceiling, then it will not be good at all. Now let's get closer to the topic and talk about specific coatings.

Laminate in the kitchen

The good thing about laminate flooring is that its installation is quite simple and you don’t need to involve professionals for this. Also, it is quite easy to care for him, he is quite durable, warm to the touch, and the choice of colors and textures is more than huge.

Overall, laminate flooring is a very good choice for a kitchen, as long as you buy it with durability in mind and don't go for the cheapest option.

Of course, a class for commercial premises is not always needed, but increased moisture resistance and resistance to chips will not hurt. By the way, just recently we wrote about that, be sure to read.

Keep in mind that a kitchen is a kitchen. A knife, a heavy frying pan, a meat grinder can fall out of your hands ... Anything. And it will be simply impossible to restore the floor later.

Also if your room is still damp, the same first floor, then laminate will not be the most brilliant choice for the reason that it has the property of "going". And if in a room of medium humidity it retains its original appearance for 10 years, then in a humid room in the fifth year, the joints will begin to “turn out”.

Do not forget that the kitchen is a place where you constantly water splashes. And the laminate does not like this very much, and you need to constantly wipe off the drops in order to keep the surface as long as possible.

Wooden floor

You can't lay parquet on your own, of course. It is expensive, subject to abrasion and, in general, not the best option for the kitchen.

But ordinary deck boards are what you need. The floor comes out very warm and without insulation, it is easy to take care of it and most importantly - no screeds are needed in this case, since the board is laid on the logs.

It is for sale ready-made, so you don’t need to scrape anything, just lay it evenly, setting the supports in level.

This option is not the most budgetary, but it is beautiful and environmentally friendly. And given that you also save on the screed, then this option has the right to be considered.

But here, too, do not forget that if a knife that fell from a height is stuck in a tree, a scratch will remain on it. But on the laminate - no. But it is unpleasant to walk barefoot on a laminate, like on oilcloth, and on a wooden one - very much so.

But, as we wrote above, it is very cold in winter.

So, if your kitchen is poorly heated, think thrice before settling on tiles. Not only is it cold in itself, it also lowers the overall degree of the room. Not much, but still.

But, if the cold does not bother you, or you are ready to insulate the floor at the stage of laying the screed, then you can consider this option.

The tile is very exacting to correctness and quality of laying. If it is poorly laid, and there are air gaps between it and the screed, then it will very quickly begin to “walk” in these places, and over time it will simply burst in this place. Also, the tile bursts from the fact that cast-iron pans fall on it ... It is unreasonable to renounce such an incident, because anything can happen and all options must be taken into account.

It is often impossible to find a replacement for broken fragments, since fashion changes quickly, the assortment in stores does too, so take this into account when buying building materials. Let you have a couple of extra tiles left for later.

Well, the last moment - the tile is often very slippery and it is very easy to slip on it if water is spilled on the floor. And falling on the tile hurts, yes. And the glasses crumble, falling on a hard surface instantly. But if they fell on a laminate or a tree, then nothing would happen to them.

As for which tile is better, it's hard to say. Naturally, it should not be for the walls, but for the floor.

If you don’t have a herd of rhinos running through your kitchen every day, you can choose the most ordinary, not the most impact-resistant. Expensive porcelain tile, for example, is definitely not needed, it is more suitable for outdoor patios.

Linoleum in the kitchen

Even a woman can put linoleum on the floor. But it must be laid exclusively on a flat surface, otherwise every grain of sand and recess will be visible under the coating. Not only is it simply ugly, it will also wipe itself in these places with incredible force.

The wear of linoleum depends on its initial characteristics. There are softer options that cannot be pressed with something hard, as a dent will instantly form. And there are denser ones, for offices and other commercial premises.

The main trouble with linoleum is that it does not shine with beautiful colors.

Color options in this case: grey, light grey, dark grey, blue. If you manage to find something more interesting and with a pattern, then it will be a great success. We do not recommend imitations of wood and tiles.

But linoleum has one big minus. On it, all the time there are black stripes from the soles, which are still a pleasure to wash. And, it's not just about street shoes.

So, if you have children in your house who run a lot and “slow down” with their soles, get ready for the fact that you will have to crawl with cotton wool soaked in acetone and wipe the marks.

Maintenance is absolutely minimal. this floor washes well. Also, it is not afraid of moisture, is not afraid of bumps and scratches, but at the same time it cannot be called very hard to the touch.

The self-leveling floor is not cold, therefore, it is much more pleasant to walk on it than on tiles.

Another big plus such floors - the ability to choose very non-standard colors. Here you can think of anything. Although the image of a volumetric aquarium with fish, with a full 3D effect.

But self-leveling floors are still a novelty, and therefore The price for them is not the most loyal.

Also of great importance is fitter skill. Some may do this very sloppily and the floor will look uneven. And considering that it is mostly glossy, every dot and bubble will be visible in the sun.

Therefore, before deciding on a self-leveling floor, look for the masters and see photos of their work, and also read reviews about this company.

And so, the self-leveling floor is very durable, they say that it has been serving for more than fifty years, while maintaining its original appearance. To be honest, we have doubts about this, since no one has canceled abrasion and micro-scratches. And, if even ceramic tiles wear out after 50 years, then how can a self-leveling floor be preserved if it is softer by definition?

Our article has come to an end and we hope you have decided a bit on which floor is better to make in the kitchen. We wish you all the best!